41 2 3
Installation Manual
Manuel d’installation
HARDWIRE KIT
TROUSSE D’ALIMENTATION PERMANENTE
RD-HWK200
©2021 PIONEER CORPORATION.
< KYTZ21H > < CRD5217-A >
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
Information to User
Alteration or modifications carried out without appropriate authorization
may invalidate the user’s right to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FEDERAL COMMUNICATIONS COMMISSION SUPPLIER’S DECLARATION
OF CONFORMITY
Product Name: HARDWIRE KIT
Model Number: RD-HWK200
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 2050 W. 190TH STREET, SUITE 100, TORRANCE, CA 90504, U.S.A.
Phone: 1-800-421-1404
URL: https://www.pioneerelectronics.com
English
After-sales service for Pioneer products
Please contact the authorized Pioneer dealer from
which you purchased this unit or an authorized
Pioneer service company for aftersales service or
questions you may have about the product. You may
contact Pioneer directly as follows:
Do not ship your unit in for repair without
contacting Pioneer first. Units sent without a
return authorization number will be refused.
USA & CANADA
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760 U.S.A.
800-421-1404
For warranty information, please see the Limited
Warranty sheet included with this unit.
Visit our website
U.S.: https://www.pioneerelectronics.com
Canada: https://www.pioneerelectronics.ca
•Learn about product updates (such as firmware
updates) for your product.
•Register your product.
•Access owner’s manuals, spare parts information,
service information, and much more.
Precautions
CAUTION
•
This product is designed for professional installation only. We recommend that only authorized
Pioneer service personnel, who have special training and experience in mobile electronics, set up
and install this product. NEVER SERVICE THIS PRODUCT YOURSELF.
• The product constantly uses vehicle power, which puts a load on the vehicle battery. If not using the vehicle
for a long period of time, or when using the vehicle for repeated short trips, power consumption from de-
vices within the vehicle may cause the battery voltage to gradually drop, and may cause the battery to go
dead. Ensure that the vehicle engine is periodically started to ensure that the battery voltage does not drop.
•
If other devices installed in the vehicle also draw from the battery when the vehicle is off, the battery may go dead
if the voltage cutoff on this product is set too high. Take care when setting voltage cutoff.
•
Do not use with anything other than Pioneer Dash Camera.
Check supported models at the Pioneer website.
U.S.: https://www.pioneerelectronics.com
Canada: https://www.pioneerelectronics.ca
•
For safety precautions, also refer to the manual of the connected Dash Camera.
•
Pioneer accepts no responsibility whatsoever for the vehicle battery losing voltage or dying.
Specifications
Input Power supply voltage 12 V / 24 V DC
Output Power supply voltage 5 V DC (maximum 1.5 A)
Voltage cutoff settings
12 V: 11.6 V / 11.8 V / 12.0 V / 12.2 V
24 V: 23.2 V / 23.6 V / 24.0 V / 24.4V
Timer off settings 1 hour / 3 hours / 6 hours / 12 hours
ACC linkage toggle switch A mode / B mode
Operating temperature −10°Cto+60°C(+14˚Fto+140˚F)
Product external dimensions (W×H×D) 45 mm × 70 mm × 22 mm (1 - 3/4 in. × 2 - 3/4 in. × 7/8 in. )
Weight 195 g (0.4 lbs)
Cable length
From the vehicle power supply to the main unit (1 m) (3 ft. 3 in.)
From the main unit to the Dash Camera (4 m) (13 ft. 2 in.)
Note
•
Product specifications and external appearance are subject to change without notice. Furthermore, the
illustrations within this manual may differ from the actual product.
Part Names and Status Indicators
LED indicator
ACC linkage switch
Refer to "Settings".
Voltage cutoff/Timer off settings
switch
Refer to "Settings".
The product status is indicated by the illumination/flashing state of the LED indicator.
If this does not light or flash as normal, try reconnecting.
LED display On Flashing*1 Flashing*2 Off*3
Power status
ACC/continuous
power on
ACC off, continuous
power on
ACC off, continuous
power on
ACC/continuous
power off
Product status Power on Parking mode on Normal recording on Power off
*1
When connecting to a Pioneer Dash Camera that supports ACC linkage, details of parking mode operation
will differ depending on the connected Dash Camera. For details, refer to the instruction manual of the
connected Dash Camera.
*2
When connecting to a Dash Camera that does not support ACC linkage, normal recording will continue
even after turning ACC off.
*3
When the timer off set time is reached, or the vehicle battery voltage drops below the voltage cutoff
settings value, the LED illumination will turn off.
Checking Connection and Mounting Parts
Main Unit ×1 Double-sided Tape ×2
Loading ...
Loading ...
Loading ...
