Loading ...
85 6 7
Before Installing the Product
Installation Precautions
•
Use the included double-sided tape to securely affix the product to the vehicle.
Bottom surface
Double-sided tape application position
•
Recommended mounting locations are within the inside the kick panel or glove compartment.
•
Mount on a flat, oil-free surface.
•
Mounting on anything other than a flat surface may result in the product falling off. Additionally, there is a
risk of malfunction.
• Mount in a location in which the product can be firmly secured. Ensure that you do not mount on places in
the vehicle that are subject to strong vibration such as the spare wheel cover board or the cargo area in a
hatchback.
•
Mounting using other than the specified mounting methods may result in diminished performance. Ad-
ditionally, there is a risk of malfunction.
•
Do not mount in the following types of locations. Failure due to high temperatures may occur.
* Locations subject to direct sunlight such as on the dashboard or the cargo area in a hatchback
* Near the heater outlet
• Do not mount in locations that may be exposed to rain or liquids, such as near a door opening or cup holder.
•
Do not mount in locations that tend to accumulate dust or dirt.
•
Do not cover with carpet or other material.
•
Mount in a location in which the cables are not subject to significant shocks.
•
Avoid mounting this product in locations in which it may be kicked or have heavy loads placed upon it.
CAUTION
•
If the fuse is blown, then replace it with a new standard glass tube fuse (diam. 5.2 mm/length 20 mm), and
tighten the tip fully.
Ensure that the fuse is replaced with one of the rated type and capacity (F 2 A L/250 V, F 500 mA L/250 V).
Connecting
Connection terminal connection and removal
•
Connect the connection terminals securely. If the terminals do not go in smoothly, they may be reversed.
Check the terminal orientation. Do not insert terminals with excessive force. Doing so may result in
malfunction.
•
When removing the connection terminals, hold the connector part to pull out. Pulling the cable may
result in connector damage.
Connection Precautions
•
Be sure to disconnect the
⊖
terminal of the vehicle’s battery before connecting the power cable.
• To prevent fuming and damage to the product, be sure to first securely connect the black lead wire (Ground)
of the product to the metal part of the vehicle body.
•
Connect separate black lead wires (Ground) for products with high current consumption. When setting up
connections all at once, there is a risk of fuming or damage to the product when screws loosen or come off
completely.
•
Always use the included parts as specified. There is a risk of product failure if other parts are used.
WARNING
•
When handling the cables, DO NOT run cables near the driver’s feet as they may interfere with the opera-
tion of the vehicle, potentially resulting in serious injury or death.
Connection diagram
Main Unit
4 m (13 ft. 2 in.)
Yellow 1 m (3 ft. 3 in.)
Red 1 m (3 ft. 3 in.)
Black 1 m (3 ft. 3 in.)
Fuse (2 A)
(F 2 A L/250 V)
Fuse (0.5 A)
(F 500 mA L/250 V)
Pioneer Dash Camera
(sold separately)
Connect to a power terminal.
+ Battery power supply (Yellow)
Always connect to a power circuit that is supplied with
power from the battery regardless of whether the vehicle
engine switch is ON or OFF.
Accessory power supply (Red)
Connect to a power circuit supplied with power when the
vehicle engine switch is turned to the ACC position.
Never install the accessory power supply to a vehicle that
does not have an ACC position on the engine switch.
Doing so may lead to a dead battery.
Ground (Black)
Securely connect to a metal part of the vehicle body.
• Connect the red and yellow lead wires to the terminals
after wiring through the vehicle’s fuse unit.
• When replacing the fuse, be sure to only use a fuse of the
rating prescribed on this product.
• Do not connect leads for other devices between the power
lead fuse and the device mounted in the vehicle.
Settings
Prior to using this product and the connected Dash Camera, configure the ACC linkage settings, voltage
cutoff settings, and timer off settings.
ACC linkage switch
Voltage cutoff/Timer off settings switch
Up: ON
Down: OFF
ACC linkage settings
Operate the ACC linkage switch in accordance with the specifications of the Pioneer Dash Camera
connecting to this product.
(Factory default: B mode)
Switch position
A mode
B mode
Specifications
of Pioneer Dash
Camera to connect
ACC-linked Dash Camera Non-ACC-linked Dash Camera
Operation after
connection
After turning the engine off (ACC off),
parking mode is activated.*
After turning the vehicle engine off (ACC
off), normal recording will continue
until the vehicle battery voltage drops
below the voltage cutoff settings value,
or the time set in the timer off settings is
reached.
Note
•
In A mode, the timer settings for this product will be disabled.
*
For details of operating conditions for parking mode, refer to the manual of the connected Dash Camera.
Check supported models at the Pioneer website.
U.S.: https://www.pioneerelectronics.com
Canada: https://www.pioneerelectronics.ca
Voltage cutoff settings
Move the voltage cutoff settings switches (3, 4) to set them depending on the vehicle battery voltage (12 V/24 V).
When the vehicle battery voltage drops below the voltage cutoff settings value, the product will automatically
stop operation.
(Factory default: 11.8 V / 23.6 V)
Switch position
Voltage cutoff settings
value (If vehicle is 12 V)
11.6 V 11.8 V 12.0 V 12.2 V
Voltage cutoff settings
value (If vehicle is 24 V)
23.2 V 23.6 V 24.0 V 24.4 V
Note
•
Depending on the usage environment and vehicle status, voltage cutoff settings values will have a margin
of error of approximately ±2 %.
Timer off settings
To use the timer off functionality, move the timer off settings switches (1, 2) to set.
After ACC off, when the set time has elapsed, the product will automatically stop operation.
(Factory default: 3 hours)
Switch position
Timer off set time 1 hour 3 hours 6 hours 12 hours
Note
•
The set time will have a margin of error of approximately ±10 %.
•
If the ACC linkage is set to A mode, then timer settings for this product will be disabled.
•
If the ACC linkage is set to B mode, then timer off settings for this product cannot be disabled.
•
When the vehicle battery voltage drops below the voltage cutoff settings value, the product will
automatically stop operation regardless of set times.
English
Loading ...
Loading ...