Dewalt DWE46155 Instruction Manual

Loading ...

English

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Surface Grinding Shroud Safety Rules

• The shroud must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The shroud is designed to collect dust and help protect the

operator from accidental contact with thewheel.

• Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safeoperation.

• Only use dry diamond surface cup wheels with this

surface grinding shroud. The surface grinding shroud

is not intended to be used with standard grinding, cut-off,

cup wheels or wirebrushes.

• The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed can

break and flyapart.

• Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and shock

theoperator.

• Always use side or bail handle. Tighten the handle

securely. The handle should always be used to maintain

control of the tool at alltimes.

• Do not use a damaged accessory. Before each use

inspect the accessory such as diamond wheel for

chips and cracks, backing pad for cracks and tear or

excess wear. If power tool or accessory is dropped,

inspect for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders away

from the plane of the rotating accessory and run

the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this testtime.

• When starting the tool with a new or replacement

wheel, hold the tool in a well protected area and let

it run for one minute. If the wheel has an undetected

crack or flaw, it should burst in less than one minute.

Never start the tool with a person in line with the wheel.

This includes theoperator.

• Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearingloss.

• Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinningaccessory.

• Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of

yourcontrol.

• Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

• Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

• Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution orshock.

• DO NOT use wire brushes with this surface

grindingshroud.

• DO NOT use abrasivewheels.

• DO NOT grind or cut metal with a diamond cup

wheel. Fragments could loosen and flyapart.

• ALWAYS use with a dustcollector.



WARNING: When not in use, place grinder

on a stable surface where it will not move

inadvertantly, roll or cause a tripping or falling

hazard. Serious personal injury mayresult.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

Loading ...

Dewalt DWE46155 4-1/2 IN. 5 IN. SURFACE GRINDING DUST SHROUD KIT

Instruction Manual - Page 5