Loading page 1...
Loading page 2...
Loading page 3...
Loading page 4...
Loading page 5...
Loading page 6...
Loading page 7...
Loading page 8...
Loading page 9...
Loading page 10...
Loading page 11...
Loading page 12...
Loading page 13...
Loading page 14...
Loading page 15...
Loading page 16...
Loading page 17...
Loading page 18...
Loading page 19...
Loading page 20...
Loading page 21...
Loading page 22...
Loading page 23...
Loading page 24...
Loading page 25...
Loading page 26...
Loading page 27...
Loading page 28...
Loading page 29...
Loading page 30...
Loading page 31...
Loading page 32...
Loading page 33...
Loading page 34...
Loading page 35...
Loading page 36...
Loading page 37...
Loading page 38...
Loading page 39...
Loading page 40...
Loading page 41...
Loading page 42...
Loading page 43...
Loading page 44...
Loading page 45...
Loading page 46...
Loading page 47...
Loading page 48...
Loading page 49...
Loading page 50...
Loading page 51...
Loading page 52...
Loading page 53...
Loading page 54...
Loading page 55...
Loading page 56...
Loading page 57...
Loading page 58...
Loading page 59...
Loading page 60...
Loading page 61...
Loading page 62...
Loading page 63...
Loading page 64...
Loading page 65...
Loading page 66...
Loading page 67...
Loading page 68...
Loading page 69...
Loading page 70...
Loading page 71...
72_ troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Surface burners do not
light.
The control knob is not set
properly.
Push in the control knob and
turn it to the LITE position.
The burner caps are not in place.
The burner base is misaligned.
Clean the electrodes.
Put the burner cap on the burner
head. Align the burner base.
Surface burner clicks
during operation.
The control knob has been left in
the LITE position.
After the burner lights, turn the
control knob to a desired setting.
If the burner still clicks, contact a
service technician.
the burners do not burn
evenly.
Surface burner components and
caps are not assembled correctly
and level.
See page 58.
Surface burners are dirty. Clean surface burner
components. (See pages 58
and 59.)
Very large or yellow
surface burner flames.
Wrong orifice is assembled. Contact your installer. Check the
burner orifice size and contact
your installer if you have the
wrong orifice. Check the LP gas
conversion.
Surface burners light
but oven burners do not
light.
The oven door lock is turned on. The display will show the Lock
icon. Hold the oven door open
and press the START/SET pad
for 3 seconds. The oven will
beep and the Lock icon will turn
o.
Gas Pressure Regulator shut o
switch is in the ‘o position.
Call a qualified service
technician.
Display goes blank.
The electrical outlet Ground Fault
Interrupter (GFI or GFCI) has been
tripped and needs to be reset.
Your digital control has been
damaged.
Replace fuse or reset circuit
breaker.
Very large or yellow
oven burner flames.
The oven burner air adjustment
shutters need to be adjusted.
Call for a qualified service
technician.
Gas supply is not properly
connected or turned on.
See the Installation Instructions
that came with your range.
Food does not bake or
roast properly in the
oven.
Wrong cooking mode is selected. See page 25-26, 36, 42.
The oven racks have not been
positioned properly for the foods
being cooked.
See page 30.
Incorrect cookware or cookware
of improper size being used.
See page 24.
Oven thermostat needs adjustment.
See page 33.
There is aluminum foil on racks
and/or oven bottom.
Remove foil.
Clock or timers not set correctly. See pages 28 and 29.
(IB)FX710BGS,FX510BGS,NX583G0VB_DG68-00356A-05_EN_120706.indd 72 06/08/2012 13:44:06
Loading page 73...
Loading page 74...
Loading page 75...
Loading page 76...
Loading page 77...
Loading page 78...
Loading page 79...
Loading page 80...