Loading ...
Loading ...
Loading ...
-
19
10 RBroompos.not ok
Hours: xxxxxhym+
Is displayed when the right side brush cannot move to
the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the right side
brush may not be raised
Confirm the message with the OK key (delete).
Turn the programme selector switch to position
C (drive).
Change to the desired sweeping programme
again.
11 LBroompos.not ok
Hours: xxxxxhym+
Is displayed when the optionally available left side brush
cannot move to the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the left side
brush may not be raised
Confirm the message with the OK key (delete).
Turn the programme selector switch to position
C (drive).
Change to the desired sweeping programme
again.
12 SBroompos.not ok
Hours: xxxxxhym+
Is displayed when the optionally available sickle brush
cannot move to the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the sickle brush
may not be raised
Confirm the message with the OK key (delete).
Turn the programme selector switch to position
C (drive).
Change to the desired sweeping programme
again.
13 Seat switch open
Hours: xxxxxhym+
Appears if the seat is left for more than 1.5 seconds in
drive mode.
– Combustion motor switches off, all brushes and the
roller brush that are lowered to the ground are raised au-
tomatically
Sit on the driver's seat.
Note: The selected sweeping / transport opera-
tion starts fully automated.
14 Usable sweeping
brush <25%
Appears if the roller brush has reached its wear limit.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying
Replace the roller brush as soon as possible to
achieve a good sweeping result.
15 MF-module not
ready to use x
Appears if the control panel has no connection to the
machine control.
– The operation of the appliance is disabled
Perform a programme selector switch reset
(OFF position).
16 Motorhood open!
Hours: xxxxxhym+
Appears if the left side cover is not properly locked in
place.
– The operation of the appliance is disabled
Completely close and lock the engine bonnet in
place.
Turn the programme selector switch to "ON".
Note: The message disappears. The appliance
is ready for operation.
17 Engine support OFF
Hours: xxxxxhym+
Appears if the battery is not sufficiently charged during
operation.
– When driving uphill, the support of the combustion mo-
tor from the battery is disabled
Confirm the message with the OK key (delete).
Drive the appliance on a level ground using the
combustion motor for a longer period of time.
This charges the battery.
18 Low battery
Hours: xxxxxhym+
Appears if the battery voltage in the sweeping mode is
so low that a start of the combustion engine is no longer
possible after switching off the appliance.
– All sweeping functions are switched off, the appliance
is still running
Note: The message can no longer be confirmed.
Drive the appliance on a level ground using the
combustion motor for a longer period of time.
This charges the battery.
19 Battery flat!
Charge externally!
Appears as soon as the programme selector switch is
turned away from the OFF position and it is recognised
that the minimum battery voltage for starting the com-
bustion engine is not reached.
– The operation of the appliance is disabled to protect
the battery
Disconnect the battery and connect it with the
correct polarity to an approved charger for
charging.
20 Firmware update
firmware update!
Appears if the machine control has detected a safety-
critical error during the self test.
– The operation of the appliance is disabled
Call service!
21 V-engine error
OFF for restart
The monitoring system for the control of the combustion
engine has detected a severe error.
– The combustion engine no longer shuts off
CAUTION! Move the main switch to the "0" po-
sition to switch the engine off!
In addition:
Perform a programme selector switch reset
(OFF position).
Subsequently:
Set main switch to “1”.
Change to the desired sweeping programme
again.
22 Call service!
+xx-xxxx-xx-xxxx
The inspection interval has lapsed. This message ap-
pears upon every start-up of the appliance.
– The appliance remains fully operational
Confirm the message with the OK key (delete).
Contact your local service for inspection under
the displayed phone number.
23 Red 0/1 switch=0
Operation locked
The message appears both during operation and start-
up of the appliance if the red main switch is in the "0" po-
sition.
– The appliance operation is prevented
Set main switch to “1”.
24 Easy oper.switch
must be OFF next
This message appears in connection with message 23. Important note: The red main switch has an
EMERGENCY STOP function.
For safety reasons the start-up of the appliance
requires the switching-off of the programme se-
lector switch (OFF position)!
46 EN
Loading ...
Loading ...
Loading ...