Loading ...
Loading ...
Loading ...
-
15
Remove the spark plug connector using
suitable tools/tongs.
Unscrew and clean spark plug.
Screw in cleaned or new spark plug.
Push on spark-plug connector.
ATTENTION
This inspection may only be carried out
when the engine is cold.
When working on the hydraulic oil tank en-
sure utmost cleanliness.
The appliance is equipped with 2 hydraulic
tanks.
– (1) The rear hydraulic oil tank is located
under the cover and is responsible for
the hydrostatic drive with the KM 105/
.... With the KM 125/... there is a filter in-
side.
Work on this hydraulic oil tank may only
be performed by the authorised cus-
tomer service.
– (2) The front hydraulic oil tank is re-
sponsible for the sweeping function
with the KM 105/... and for all hydraulic
functions with the KM 125/....
Figure: Front hydraulic oil tank
1 Screw
2 Hydraulic oil tank
3 Deaeration valve
Filler neck
4 Oil dipstick
Unscrew and pull out the screw for the
attachment of the hydraulic oil tank.
Swivel the tank towards the front until it
is held in the final position by a belt.
Unscrew and withdraw oil dipstick.
Wipe off and insert the oil dipstick (do
not turn it in).
Remove the oil dip one more time and
check the oil level.
The filling level should be between the
"Max" and "Min" marking.
If hydraulic oil is missing:
Refill hydraulic oil.
For oil type refer to Chapter "Technical
specifications".
Reinsert the oil dipstick.
Note: The side brush floating mounting ad-
justs the sweeping track as the bristles
wear down. The side brush must be re-
placed if it becomes too worn.
Recommendation: Replacing the side
brush at a remaining bristle length of ap-
prox. 10 cm.
Park the machine on an even surface.
Turn the programme selector switch to
"OFF" and remove the KIK-key.
Note: The side brush is raised.
Unscrew all 3 star grip nuts at the bot-
tom of the side brush by hand. For this
purpose reach through the bristles of
the side brush.
Remove the wiper blade.
Clip new side brushes on to driver and
screw on.
Park the sweeper on an even surface.
Activate parking brake.
With appliance with low emptying
system:
Turn the programme selector switch to
"OFF" and remove the KIK-key.
Remove both waste containers.
Remove belts or cords from roller
brush.
With appliance with high emptying
system:
Turn the programme selector switch to
"ON".
Lift the waste container and secure by
means of cylinder support.
Remove belts or cords from roller
brush.
The sweeping track of the roller brush is au-
tomatically adjusted by a system called
TEACH.
The condition of the roller brush can be
shown on the display.
Turn the programme selector switch to
"ON".
Push the direction key "upwards" or
"downwards" until the display > usabil-
ity of the roller brush: ..%< appears.
Note: If the roller brush is heavily worn, the
indication >Usability of the roller brush
<25%< appears on the display.
Now, at the latest, the roller brush should
be replaced.
The replacement is required if the sweep-
ing result visibly decreases due to the wear
of the bristles or the indication >Usability
of the roller brush <25%< appears on the
display.
Each roller brush half is attached to the
shaft by means of 2 screws. Both halves
are identical, which facilitates the installa-
tion.
Park the machine on an even surface.
Activate parking brake.
With appliance with low emptying
system:
Turn the programme selector switch to
"OFF" and remove the KIK-key.
Remove both waste containers.
Note: For the removal of the roller
brush dismount the centre bar first.
Loosen the screw and remove the cen-
tre bar.
The next steps for removing the roller
brush are described in the following
Chapter "With devices with high empty-
ing system".
With appliance with high emptying
system:
Turn the programme selector switch to
position C (drive).
Lift the waste container and secure by
means of cylinder support.
Turn the programme selector switch to
"OFF" and remove the KIK-key.
1 Screws
2 Roller brush
Unscrew both screws by hand and pull
the roller brush half from the shaft.
Check hydraulic oil level and refill
hydraulic oil
Checking the sweeping mirror of the
side-brushes
Replacing side brush
Checking roller brush
Check the sweeping mirror of the
sweeping roller
Replacing the roller brush halves
42 EN
Loading ...
Loading ...
Loading ...