Loading ...
Loading ...
Loading ...
ENGLISH
12
Accessories
WARNING:
Since accessories, other than those
offered by
CRAFTSMAN
, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN
recommended accessories should be used
with thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1-888-331-4569.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing thisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
Using the Grease Gun (Fig.A)
WARNING: To reduce the risk of serious personal
injury, always maintain a grip on the handle
when operating the grease gun or positioning the
hose ontofittings.
1. To operate the grease gun, hold the grease gun by the
handle
3
, or place it on a stable surface upright on its
rubber feet
17
maintaining a grip on the handle.
2. Holding the hose by the flexible hose safety spring
guard
7
, connect the flexible hose grease coupler
8
or
other appropriate grease coupler, onto the grease fitting
to be filled.
3. Carefully depress the variable speed trigger switch to
begin the filling process. Once the correct amount of
grease has been dispensed, release the trigger and
remove the coupler from the grease fitting.
4. If the coupler does not release, there may still be residual
pressure in the line. Moving the coupler from side to side
can relieve the residual pressure so it can be removed
from the coupling.
5. If the coupler leaks excessively or does not hold on to the
grease fitting, it should bereplaced.
Installing and Removing the Battery Pack
(Fig.H)
WARNING: Ensure the tool/appliance is in the off
position before inserting the batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
1. To install the battery pack
15
into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does notdisengage.
2. To remove the battery pack from the tool, press the
release button
16
and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of thismanual.
Proper Hand Position (Fig. M)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the flexible hose
safety spring guard
7
with the other hand on the handle
3
asshown.
Speed Selection (Fig.A)
The CMCGG001 features two speed settings for
greaterversatility. Speed 1, low output/high PSI, is
recommended for general lubrication applications. Speed 2,
high output/low PSI, is recommended for general lubrication
applications not requiring high PSI such as large bearings or
filling areas where a lot of grease is required.
NOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changingspeed.
1. To select speed 1 (low output/high PSI), turn the tool
off and permit it to stop. Slide the speed selector
21
up
towards the motor housing
5
.
2. To select speed 2 (high output/low PSI), turn the tool off
and permit it to stop. Slide the speed selector
21
down
towards the handle
3
.
NOTE: If the tool does not change speeds, confirm that
the speed selection switch is completely engaged in the
speed 1 or speed 2position.
MAINTENANCE
WARNING:
To reduce the risk of serious personal
injury, turn unit off and
remove the battery pack
before making any adjustments or removing/
installing attachments, accessories or when filling
with grease. An accidental start‑up can causeinjury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
OPERATION
WARNING:
To reduce the risk of serious personal
injury, turn unit off and
remove the battery pack
before making any adjustments or removing/
installing attachments, accessories or when filling
with grease. An accidental start‑up can causeinjury.
Loading ...
Loading ...
Loading ...