Loading ...
Loading ...
Loading ...
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) ofoil with 1 gallon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or marine oil. These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor clean-
er products in the fuel tank or permanent dam-
age may occur. See the STO RAG E section for
additional information.
HELPFUL TIP I
lf your engine switch reads
' "push to stop'; it is always
in the ON position.
HOW TO STOP YOUR UNIT
• To stop the engine, push and hold the STOP
switch in the STOP position until the engine
stops.
• If engine does not stop, move choke to the
FULL CHOKE position.
HOW TO START YOUR UNIT
_I_WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
HELPFUL TIP I
/f your engine still does not
I start after foflowing these I
instructions, pleas e call
1-800-554-5723.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
_ Starting Position
1. Set unit on a fiat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
4. Squeeze the throttle trigger fully and hold
through al! remaining steps.
Primer
Lever
Starter Handle
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
puII rope more than 6 times.
6. As soon as engine sounds as ifit is trying to
start, move choke lever to HALF CHOKE
position.
7. Pull starter rope sharply until engine runs.
but no more than 6 pulls.
NOTE: If the engine doesn't start after 6
pulis (at the HALF CHOKE position).
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hoid the
throttle trigger and puff the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn't
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8. Once the engine starts, allow itto run 10 se-
conds, then move the choke lever to the
RUN position. Allow the unit to run for 30
more seconds at RUN before releasing the
throttle trigger.
NOTE: If engine dies with the choke le-
ver in the RUN position, move the choke
lever to the HALF CHOKE position and
pull the rope until engine runs, but no
more than 6 pulls.
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
2. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the en-
gine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
4. Allow engine to run 15 seconds, then move
the choke lever to RUN.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
5
Loading ...
Loading ...
Loading ...