Loading ...
Loading ...
Loading ...
User’s Manual
16
English / English
Before installing the components, please carefully read all of the instructions contained in this manual. It is advisable to carefully follow
the highlighted instructions. Failure to comply with these instructions may cause unintentional harm or damage to the components
SAFETY CONSIDERATIONS
1. Make sure your vehicle/vessel has 12 VDC voltage negative ground electric system.
2. Check your alternator and battery condition to ensure they can handle the increased consumption.
3. Do not carry out any installation inside the engine compartment or in areas exposed to water, excessive humidity, dust or dirt.
4. Never run cables outside the vehicle/vessel or install the amplifier next to electronic gearcases.
5. Install the amplifier in the vehicle/vessel sections where temperature is between 0°C (32°F) and 55°C (131°F). Leave at least 5 cm (2 “) of space around
the amplifier. There must be good air circulation where the amplifier is installed. If you cover the heat sink, the amplifier goes into protection mode.
6. The amplifier can reach temperatures of around 80°C (176°F). Make sure it is not dangerously hot before touching it.
7. Make sure the location you chose for the components does not affect the correct functioning of the vehicle/vessel mechanical and electrical devices.
8. Make sure the power cable is not short circuited during installation and connection with the battery.
9. Make sure all the cables are properly secured along their entire length. Also, make sure their outer protective jacket is flame resistant and self
extinguishing. Secure the connected cables close to the terminal blocks with wire ties or clamps.
10. When positioning the power supply cable, avoid to run the wire over or through sharp edges or close to moving mechanical devices. Use rubber
grommets to protect the wire if it runs in a hole of the plate or proper materials if it is close to heat-generating parts.
11. Make sure all the cables are properly secured all along their length. Also, make sure their outer protective jacket is flame resistant and self
extinguishing. Use a clamping screw to secure positive and negative cables just close to the amplifier respective power supply terminal blocks.
12. Choose the cable gauge according to the amplifier power and to the suggestions you can find here. Use high quality cables, connectors and
accessories, as you can find in the Connection catalogue.
13. Pre-plan the configuration of your new amplifier and the best wiring routes to ease installation.
14. In order to avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
15. Always wear protective eyewear when using tools, as splints or product residue may become airborne.
TYPICAL INSTALLATION SEQUENCE
If you have any questions please refer to the User’s Manual you can find available on www.hertz-audio.com or contact your HERTZ dealer or Hertz
authorized service for assistance.
1. Before installing the amplifier turn off the source and all other electronic devices in the audio system to prevent any damages.
2. Using a cable with adequate AWG (see chart: Power Supply Cable), run the power wire from the battery location to the amplifier mounting location.
3. Connect the power supply with the correct polarity. Connect (+) terminal to the cable coming from the battery and (-) terminal to the vehicle/vessel chassis.
In other applications, like a motorcycle, it is recommended to connect both (-) and (+) terminals cables directly to the battery
4. Put an insulated fuse holder 40 cm max far from the battery positive terminal; connect one end of the power cable to it after the other end to the
amplifier. Do not mount the fuse.
5. To ground the device (-) in the right way, use a screw in the vehicle/vessel chassis; scrape all paint or grease from the metal if necessary,
checking with a tester that there is continuity between the battery negative terminal (-) and the fixing point. If possible, connect all components
to the same ground point; this solution rejects most noise which can be generated during the audio reproduction.
6. Route all signal cables close together and away from power cables.
7. Connect the RCA input cables, the applied signal must be between 0.6 VRMS and 6 VRMS.
8. Connect the high level inputs using the proper plug. Applied signal must be between 2.2 VRMS and 22 VRMS.
9. Connect the speaker output using 10 AWG max speaker cable.
10. Don’t connect (-) Ch1 and (-) Ch2 , (-) Ch3 and (-) Ch4 speaker outputs together. If you use an external stereo crossover, make sure that its negative poles
are not connected together.
11. The amplifier turns on by connecting the remote turn on terminal (REMOTE IN) to the source specific output. The amplifier turns on automatically,
without remote signal, connecting a source loudspeakers’ outputs (BTL) to the inputs by setting the “DC REM” switch to ON position.
12. The LED on the front panel lights up green indicating that the product is on. The LED lights up red if the outputs go on overload, if the thermal
protection is triggered, if the speaker cables short circuits with the vehicle/vessel chassis and if the amplifier is malfunctioning
13. Secure all auxiliary devices you built to install the components to the vehicle/vessel structure; this ensures stability and safety while driving.
The amplifier detachment while driving may cause serious damage to the passengers, as well as to other vehicles/vessels.
14. When installation is over, check the system’s wiring and make sure all connections were done properly.
15. Put the fuse into the fuse holder. The fuse value must be 60A
16. Listening level calibration is made by adjusting the source volume up to 3/4 of its maximum level; then, adjust the amplifier levels until you hear distortion.
17. Warranty Certificate: please check out the HERTZ website for further information.
SAFE SOUND
USE COMMON SENSE AND PRACTICE SAFE SOUND. PLEASE REMEMBER THAT LONG EXPOSURE TO EXCESSIVELY HIGH SOUND PRESSURE LEVELS MAY
DAMAGE YOUR HEARING. SAFETY MUST BE AT THE FOREFRONT WHILE DRIVING
Information on electrical and electronic equipment waste (for those European countries which organize the separate collection of waste)
Products which are marked with a wheeled bin with an X through it can not be disposed of together with ordinary domestic waste. These electrical and electronic products must
be recycled in proper facilities, capable of managing the disposal of these products and components. In order to know where and how to deliver these products to the nearest
recycling/disposal site please contact your local municipal office. Recycling and disposing of waste in a proper way contributes to the protection of the environment and to prevent
harmful effects on health.
1
PRECAUTIONS
Loading ...
Loading ...
Loading ...