Loading ...
Loading ...
Loading ...
Troubleshooting
Error Codes
Solutions
Error Code
Possible Cause
E1
It takes over minutes to
fill water but cannot achieve
its preset water level.
30
Check for Washer not filling
properly and Water leakage.
E2
The top lid is open. Close the lid.
E3
The washer runs out of
balance for three times.
Redistribute the load.
E4
It takes over minutes to
drain water but can not
drain the washer empty.
10
Check for Washer will not
drain water.
E5
The water fills too much
to exceed its preset level.
Call to service center for help.
Before calling for service
Problem Possible Cause
Washer not
filling
properly
Water leaks
every load
Hoses not installed
correctly.
Check all fi ll and drain hose connections
to ensure that they are tight and secure.
Filter clogged.
Inlet hoses may be
kinked Insufficient
water supply.
The washer lid is open.
Hot and cold inlet
hoses are reversed.
Water level is too low.
Water inlet valve
damaged.
Disassemble the water inlet hose and clean
the inlet point. Check that inlet hoses are
not kinked or clogged.
Make sure that both hot and cold water
faucets are turned on all the way.
The washer will not operate if the lid is open.
Close the lid and
make sure that nothing
is caught under the lid preventing it from
closing completely.
Check inlet hose connections. Make sure
the hot water supply
is connected to the
hot inlet valve, and the cold water supply
is connected to the cold inlet valve.
This is a high e ff ic ie nc y was he r. The
water will not normally
cover the clothes.
The fill level is optimized for the wash
motion to achieve the best wash performance.
Call to the service center for service.
SolutionsProblem
27
28
The following symbols provide garment care direction. The Clothing care labels
include symbols for washing, bleaching, drying and ironing, or dry cleaning when
necessary. The use of symbols ensures consistency among garment manufacturers
of domestic and imported items. Follow care label directions to maximize garment
life and reduce laundering problems.
APPENDIX
Fabric Care Chart
** The number of dots represent appropriate wash water temperatures for various
items. The temperature range for Hot is 105°-125°F/41°-52°C, for Warm 85°-105°F/29°-41°C
and for Cold 60°-85°F/16°-29°C.(Wash water temperature must be a minimum of
60°F/16°C for detergent activation and effective cleaning.)The clothes washer can
not ensure these temperatures because the actual temperature of the water entering
your washer depends on water heater settings and regional water supply temperatures.
For example, cold water entering the home in the northern states during winter may
be 40°F/4°C which is too cold for effective cleaning. In this situation, you will need
to adjust the water temperature by selecting a warm setting, adding some hot water
to the MAX FILL line, or using your Washer’s heating option, if available.
Wash Cycle Special Instructions
Normal
Line Dry/ Hang to Dry
Permanent Press /
Resistant / Wrinkle Control
Wrinkle
Drip Dry
Gentle/Delicates
Dry Flat
Hand Wash
Water Temperature**
High
Hot
Medium
Warm Low
Cold
Any Heat
Bleach
No Heat/Air
Any Bleach (when needed)
Iron-Dry or Steam
Temperatures
Only Non-Chlorine
(color-safe)
Bleach (when needed)
High
Tumble Dry Cycle
Medium
Low
Gentle/ Delicates
Warning Symbols for laundering
Do Not Wash
Do Not Wring
Do Not Bleach
Do Not Tumble Dry
No Steam (added to iron)
Do Not Iron
Dry Clean
Do Not Dry Clean
Line Dry/ Hang to Dry
Drip Dry
Dry Flat
For machine-washable
wool. Loads should be
under 8 pounds.
Heat Setting
Normal
Permanent Press /
Resistant / Wrinkle Control
Wrinkle
Dryclean
Loading ...
Loading ...
Loading ...