Extra Tall & Wide Safety Gate
INSTRUCTION MANUAL
Please read the following instructions carefully.
Keep this instruction manual and save for future reference.
Tools required: Phillips head screwdriver, drill (for top of stair installation),
and pencil (not included), wrench (included).
For use with children from 6 - 24 months.
Keep small parts away from children.
Adult assembly required.
Fits openings from 29.5" - 53" wide.
33180
Children have died or been seriously injured when gates are not securely installed.
• ALWAYS install and use gate as directed using all required parts.
• Install according to manufacturer’s instructions.
• Stop using when a child can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• To prevent falls, never use at top of stairs without wall mounting cups and door stopper.
• NEVER use a gate to keep child away from pool.
• NEVER leave child unattended.
• ALWAYS close and lock the gate behind you.
• This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
• Do not use if any components are missing or damaged.
• Adult assembly required. Exercise care when unpacking and assembling product.
CAUTION: KEEP SMALL PARTS OUT OF CHILD’S REACH.
WARNING
components:
Gate Door
Gate Frame
A
B
Large Extension Frame 1
Large Extension Frame 2
C
D
Small Extension Frame
Lower Latch
Top Latch
E
Tension Bolts with Tension Nuts (4)
Wall Cups (4)
Adhesive Mounting Pads (4)
I
J
Wall Anchors (4)
K
L
Screws (4)
M
Extension Pins (4)
Door Stop
F
G
H
Wrench
N
O
2
hardware:
I
x4 x4
J
K L
M N
x4 x4
x4x4
O
x1
C ED
B
F
A
G
H
gate configurations (choose which best fits your scenario):
Measure the width of the opening where you intend to install the gate.
Refer to the following illustrations to determine the correct installation
conguration. Baseboard molding may change which conguration is
appropriate.
A B
D
(29.5˝- 33˝) without extension frames
(33.5˝- 37˝) with small extension frame
(37.5˝- 41˝) with large extension frame (41.5˝- 45˝) with large and small extension frame
WARNING
NEVER install three extension
frames on the same side of the
gate.
!
Note: This instruction book
illustrates installation of gate
conguration F.
If choosing gate conguration A,
skip ahead to step 2. Otherwise,
follow step 1 using the
appropriate extension frames that
best t your scenario.
3
Important: Gate includes a door stop (part H)
which prevents the gate from swinging open
in one direction. When installing the gate at
the top of stairs, be sure that the door stop is
on the stairway side of the gate so the door
cannot open over the stairs. While the door
stop comes assembled on the gate, it can be
removed and installed on either side of the
gate frame.
When gate is not used at top of stairs, door
stop may be removed to allow gate door to
open in either direction.
!
H
E
C
(45.5˝- 49˝) with 2 large extension frames
F
(49.5˝- 53˝) with the 2 large and small extension frames
4
installation:
2
Slide tension bolts
into upper and lower holes
on both sides of
extension frames
(or gate frame if no extensions
are being used).
J
x 4
1
I
x 4
x 4
Connect the extension
frames to the gate frame by
inserting the extension pins into the holes
in the extension frame, or into the gate frame
(if extensions are not being used).
installation (continued):
Check locations A and B. The
distance between the gate and the
wall should never exceed 2.75”.
4
3
5
A
B
tighten!
tighten!
tighten!
tighten!
5
Note: If mounting at top of stairs, proceed to step 6. Otherwise, follow the
directions in step 14 to tighten the tension nuts.
!
Use the tension nuts
to tighten both of the
bottom tension bolts.
Use the tension nuts
to tighten both of the
top tension bolts.
Stand the gate in the
center of the opening.
Make sure the bottom of
the gate is completely flush
to the floor. Slide tension
bolts out until they
contact the door frame
or wall on both sides.
IMPORTANT
7
6
6
STOP! wall cup/top of stairs installation:
WARNING
For use at top of stairs, wall cup
installation is MANDATORY.
Follow these wall cup installation instructions when using gate at TOP OF STAIRS
(MANDATORY), or if using wall cups for a standard opening (optional). If opting not to use
wall cups for a standard opening, skip ahead to step 14.
Use the pencil to trace
the entire outline
of each tension bolt
directly onto the wall.
x 4
Loosen the
lower and upper
tension nuts and
remove gate.
loosen!
loosen!
x 2
x 2
Door stop must be
on stair side of gate.
Gate door must
open away from
stairs.
!
At the top of the
landing, position the
gate a minimum of 3-6
inches (8-15cm) away
from the top step.
IMPORTANT
8
x 4
Mark drill
holes with a
pencil through
the center
of each wall cup.
Mark drill
holes with a
pencil through
the center
of each wall cup.
x4
Place a wall cup over
the center of each circular
outline on the wall.
Place a wall cup over
the center of each circular
outline on the wall.
wall cup/top of stairs installation (continued):
1
st
Drill a 7/32
'
'
pilot hole
into each of the 4
center marks.
Drill a 7/32'' pilot hole
into each of the 4
center marks.
2
nd
Insert wall anchors
into pilot holes.
Insert wall anchors
into pilot holes.
7
9
M
L
Note: If mounting into plaster or
drywall, follow this step and use
the wall anchors provided.
!
Attach one pad to
the back of each
wall cup.
peel
peel
2
nd
3
rd
Remove backing
from one side of each
adhesive mounting pad.
Remove
backing.
1
st
10
wall cup/top of stairs installation (continued):
press
press
press
press
11
8
x 4
K
x 4
L
Align the wall cups so
the center hole is placed
directly over the wall anchor.
Stick wall cups to the wall.
Make sure
all wall cups
are facing up.
Make sure
all wall cups
are facing up.
!
!
Note: The bottom wall cups
should rest on the oor.
Repeat "installation"
steps on page 5.
The 4 tension bolts
will rest within
each wall cup.
x 4
x4
Screw
wall cups
into wall.
x 4
wall cup/top of stairs installation (continued):
12
13
9
N
NEVER open gate door over stairs.
IMPORTANT
wall cup/top of stairs installation (continued):
10
O
Tighten all 4
tension nuts
with the provided
wrench.
x 4
14
FINISHED!
Tighten top tension nuts
inward toward the gate
frame at the same time
so that the upper
latch/handle goes below
the release button
completely.
Tighten top tension nuts
so that the upper
latch/handle goes below
the release button
completely.
operation:
to unlock gate: hold open feature:
First, slide locking
tab back to release.
Second, lift gate
door open.
To activate,
open gate door
at least 90º in
either direction.
testing the installation:
Close the gate.
Make sure the
upper and lower
latches lock
securely.
push!
push!
Push the gate and
extension frames
to check
stability.
1
st
1
st
2
nd
2
nd
11
Colors and styles may vary.
MADE IN CHINA.
4/19
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
401-671-6551
© 2019 Summer Infant (USA), Inc.
If the gate does not close properly:
1. Gate is not properly aligned in the door
frame.
Solution: To adjust the gate’s alignment,
loosen all four tension bolts and reposition
gate so that it matches the “correct” image.
Re-tighten tension bolts.
2. Pressure of tension bolts needs to be
adjusted.
Solution: Loosen or tighten the upper tension
bolts. Ensure the upper latch engages securely
when the gate swings closed, and that it can
be released properly when the sliding lock tab
is pushed back.
troubleshooting:
maintenance:
replacement hardware kit #27930-50
• Regularly check tension bolts to make sure the gate is securely in place.
• Do not use the gate if any components are damaged or missing.
• Surface clean with a damp cloth or sponge using mild detergent and warm water.
correct!
incorrect!
