Loading ...
Loading ...
Loading ...
E-87
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm screens until the one whose time you want to set
is displayed.
AL-1 AL-2 AL-3
SIG* SNZ AL-4
D
* There is no time setting for the hourly time signal.
2. Hold down
A
until
SET Hold
appears on the display and then the
current settings start to fl ash.
• This is the setting screen.
3. Press
C
to move the fl
ashing between the hour and minute settings.
4. While a setting is fl ashing, use
D
(+) and
L
(–) to change it.
• When setting the alarm time using the 12-hour format, take care to
s
et the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press
A
to exit the setting screen.
• Setting an alarm time causes that alarm to turn on automatically.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Alarm ON/OFF indicator
E-86
Using the Alarm
You can set fi ve independent daily alarms. When an alarm is turned on,
an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the
watch is not in the Timekeeping Mode. One of the daily alarms is a
snooze alarm. The snooze alarm will sound every fi ve minutes up to
seven times or until it is turned off. You can also turn on an Hourly Time
Signal, which will cause the watch to beep twice every hour on the hour.
Note
• The alarm will sound even if the watch is in the Diving Mode.
• Set the time before entering the Diving Mode.
To enter the Alarm Mode
Use
C
to select the Alarm Mode (
ALM
) as shown on page E-26.
• About one second after
ALM
appears on the display, the display will
change to show an alarm name (
AL-1
to
AL-4
, or
SNZ
) or the
SIG
indicator. The alarm name indicates an alarm screen.
SIG
is shown
when the Hourly Time Signal screen is on the display.
• When you enter the Alarm Mode, the data you were viewing when you
last exited the mode appears fi
rst.
l
l
l
l
l
l
l
l
l
l
Alarm name
(AL-, SNZ, or SIG)
Alarm time
(Hour : Minutes)
Current time
E-85
4. Use
D
(+) and
L
(–) to change the fl ashing item.
• To set the starting value of the countdown time to 24 hours, set 0H
00’00.
5. Press
A
to exit the setting screen.
To perform a countdown timer operation
D
D
D D
A
Start Stop (Resume) (Stop) Reset
• Before starting a countdown timer operation, check to make sure that a countdown operation is not in
progress (indicated by the seconds counting down). If it is, press
D
to stop it and then
A
to reset to
the countdown start time.
• An alarm will sound and the graphic dial will fl ash for ten seconds when the end of the countdown is
reached. This alarm will sound in all modes. The countdown time is reset to its starting value
automatically after the alarm stops sounding.
To stop the alarm
Press any button.
E-84
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
Note
• The time up alarm will sound even if the watch is in the Diving Mode. Perform the start operation before
entering the Diving Mode.
To enter the Countdown Timer Mode
Use
C
to select the Countdown Timer Mode (
TMR
) as shown on page E-26.
• About one second after
TMR
appears on the display, the display will
change to show the countdown time hours.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
d
own), press
D
to stop it and then press
A
to reset to the current
countdown start time.
• If a countdown is paused, press
A
to re
set to the current
countdown start time.
2. Hold down
A
for at least two seconds.
• SET Hold will fl ash on the display and then the current start time
setting will start to fl ash. Keep
A
depressed until the start time
setting starts to fl ash.
3. Press
C
to move the fl ashing between the hour and minute settings.
l
l
l
l
l
l
l
l
l
l
Countdown time
(Hour, minutes, seconds)
Current time
E-83
To measure two fi nishes
D
A D A A
Start Split
First runner fi nishes.
(
SPLIT
appears in
the upper part of the
display.)
Display time of fi rst
runner
Stop
Second runner
fi nishes.
Split release
Display time of
second runner
Reset
Note
• The Stopwatch Mode can indicate elapsed time up to 99 hours, 59 minutes, 59.99 seconds.
• Once started, stopwatch timing continues until you press
D
to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi
ned above. A paused timing
operation will remain paused until you press
D
to restart it or
A
to reset.
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns
to elapsed time measurement.
E-82
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
C
to select the Stopwatch Mode (
STW
) as shown on page E-26.
To perform an elapsed time operation
D
D D D A
Start Stop (Resume) (Stop) Reset
To pause at a split time
D
A A D A
Start Split
(
SPLIT
appears
in the upper part
of the display.)
Split release Stop Reset
l
l
l
l
l
l
l
l
l
l
Hours
Minutes
Current time
Seconds
1/100 second
E-81
To delete a specifi c time stamp record
1. Enter the Time Recall Mode.
2. Use
D
to display the record you want to delete.
Important!
• Note that holding down
A
fo
r more than about fi ve seconds in step 3 will delete all time stamp
records.
• Once a record is deleted, it cannot be recovered.
3. Hold down
A
for about two seconds. First,
CLEAR Hold
will fl
ash on the display. After that,
CLEAR
will stop fl ashing and remain display. Release
A
as soon as
CLEAR
stops fl ashing.
• Deleting a record displays the record that comes after it.
• If the time record you delete is the last one stored in memory, the message NO
-DATA will scroll on
the display.
To delete all time stamp records
1. Enter the Time Recall Mode.
2. Hold down
A
for about fi ve seconds. First,
CLEAR ALL Hold
will fl ash on the display. After that,
CLEAR ALL
will stop fl ashing and remain display. Release
A
as soon as
CLEAR ALL
stops fl ashing.
• The message NO
-DATA will scroll on the display to indicate that all time stamp records have been
deleted.
E-80
Display of Time Stamp Records Created in Each Mode
Other Modes Thermometer Mode
Digital Compass ModeDiving Mode
Record Number
Water Depth
(alternates with water temperature
and the hour, minute, second)
Bearing
(alternates with hour,
minute, second)
Temperature
(alternates with hour,
minute, second)
Month, dayHour, minute,
second
• Pressing
A
displays the date (year, month day) and time for about two seconds.
Operation Guide 3445
Loading ...
Loading ...
Loading ...