Loading ...
Loading ...
Step 2
Using Your Personal Steam Inhaler
9. Adjusting steam intensity:
A. For More Steam: Move the Steam Disk Control
clockwise for maximum steam.
B. For Less Steam: Move the Steam Disk Control
counterclockwise for minimum steam. If at any
time the treatment becomes too intense, stop
treatment immediately.
10. When treatment is complete, move Power Switch to the
OFF position. The Indicator Light will go out. Disconnect
plug from electrical outlet. Allow the appliance to cool
for at least 20 minutes before moving or refilling it (see
Care and Cleaning section).
DO NOT operate Steam
Inhaler when empty.
NOTE: Steam Inhaler will automatically shut-off when
water runs out. If this happens, move Power Switch to
OFF position and unplug unit.
Step 4
1. Fully unravel cord. Failure to do so could cause
overheating and possible fire hazard.
DO NOT use
with extension cords or power strip. Place Inhaler on a
flat, stable surface for use.
2. Unlock the Top Housing from the Base by twisting the
Top Housing counter clockwise. When fully unlocked,
the arrow on the Top Housing will align with the
unlock symbol on the Base. Lift the Top Housing
straight up and set aside.
3. Fill Water Reservoir with up to 2.5 tablespoons (40 mL)
of cool tap water.
DO NOT fill above Heating Element.
Use with water only.
DO NOT add any essential oils,
medication or inhalant liquids such as Vicks
®
VapoSteam
or Kaz Inhalant, to the Water Reservoir. An unsafe condition
may result if anything is added to the water.
4. Place Top Housing on the Base and twist clockwise to
lock. When fully locked, you will feel a click and the
arrow on the Top Housing will align with the lock
symbol on Base.
5. Place Mask on Top Housing and gently push down to
ensure Mask is secure.
CAUTION: NEVER move, lift, shake or tilt the Inhaler
while it is in use or while it contains hot water.
DO NOT
remove the Mask or Top Housing after turning ON the
Inhaler. Steam is produced by boiling water; tilting or
shaking unit can cause water to spill and possible burns.
CAUTION: DO NOT block any vents.
6. Connect cord to electrical outlet. DO NOT use with
extension cord or power strip. Press the On/Off Switch to
the ON position. The Indicator Light will illuminate.
7. The Steam Inhaler will take approximately 6 minutes
to begin making steam. Use caution, the Water
Reservoir and water will become hot.
8. Place your face over the Mask. DO NOT rest your face
on the Mask. Breathe normally through your nose and
mouth, inhaling steam into your nasal and throat
passages. Continue treatment for five to fifteen minutes.
$
$
Step 3
2.5 Tbsp.
Step 9 A
Step 9 B
Step 8
Step 5
4 5
Step 2
Step 1
Your Vicks Steam Inhaler can be used with Vicks VapoPads
®
,
to provide up to 8 hours of soothing vapors. One free sample
of the menthol VapoPad is included with your device.
To use your unit with scent pads, ensure that the unit is OFF
and follow these instructions:
1. Gently slide out the VapoPad Tray from the back of the
Top Housing. Note: Only slide Tray out. DO NOT attempt
to detach the Tray from the Top Housing.
2. Open VapoPad sachet by tearing notch on pad bag.
DO NOT touch pad with hands. If pad is touched, do not
rub face or eyes as it may cause irritation.
3. Insert Vicks VapoPad with angled end at the front of the
tray. Up to two scent pads can be inserted, one in each
slot of the VapoPad Tray. Push VapoPad Tray in to close.
4. When the VapoPad is dried and no longer providing
scent, discard.
NOTE: DO NOT operate Steam Inhaler if VapoPad Tray is
missing or not secured.
This Steam Inhaler (with or without Vicks VapoPads)
is not recommended for use by children.
Using Vicks
®
VapoPads
®
Step 3
Loading ...
Loading ...
Loading ...