Ancona AN-22118SS 2-piece Kitchen Appliance Package with 36" 6-burner Gas Cooktop with 1200CFM Undercabinet Range Hood

User Manual - Page 16

For AN-22118SS. Also, The document are for others Ancona models: AN-2160, AN-2161, AN-2162, AN-2230SS, AN-2236SS, AN-2248SS, AN-2230WHT, AN-2236WHT, AN-2248WHT, AN-2230SSBK, AN-2236SSBK, AN-2248SSBK

PDF File Manual, 55 pages, Read Online | Download pdf file

AN-22118SS photo
Loading ...
Loading ...
Loading ...
— 16 —
Maintenance
Problem Possible Cause
If the range hood or LED light
does not operate after installation:
Check if the range hood has been plugged in, make sure that all power
has been turned back ON, fused not blown and all electrical wiring are
properly connected.
The range hood vibrates when the
blower is on:
The range hood might not have been secured properly on to the ceiling or
wall.
The blower or fan seems weak:
Checkthattheductsizedusedisatleasttwo6in.(15.3cm)or8in.(20.3
cm) or 3 1/4 × 10 in. (8.3 × 25.4 cm). Range hood WILL NOT function
efcientlywithinsufcientductsize.Forexample:9in.(22.8cm)ductover
8 in. (20.3 cm) hole and loosely secured.
Checkifductiscloggedorifdamperunit(half-circularange)isnot
installed correctly or opening properly. A tight mesh on a side wall cap unit
mightalsocauserestrictiontotheairow.
The lights work but the fan is not
spinning at all, is stuck or is rattling:
The fan might be jammed or scraping the bottom due to shipping damage.
Please contact us immediately.
The hood is not venting out
properly:
Make sure the distance between the stove top and the bottom of the hood
is within 24 in. and 30 in. (61 and 76.2 cm) in distance.
Reduce the number of elbows and length of duct work. Check if all joints
are properly connected, sealed, and taped.
Troubleshooting
Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks.
For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder
with a little water and a soft cloth.
For stubborn cases, use a plastic scouring pad or soft bristle brush with cleanser and water. Rub lightly in direction of
polishing lines or “grain” of the stainless nish. Avoid using too much pressure, which may mar the surface.
DO NOT allow deposits to remain on surface for long periods of time.
DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust.
DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after
exposure and wipe dry with a clean cloth.
Painted surfaces should be cleaned with warm water and mild detergent only.
Cleaning Filters
IMPORTANT: Drain oil from baffles, spacers, filters, oil tunnels, oil containers before oil and residue overflow!
Removeallbafes,spacers,lters,greasetray,andoilcontainersanddiscardoilandresidue.
Washwithwarmsoapywater.NOTE:Stainlesssteelbafes,spacersandoiltunnelaretoprackdishwashersafe.
Dry thoroughly before replacing and follow directions for installation in reverse.
Filters should be cleaned after every 30 hours of use.
Should lters wear out due to age and prolonged use, replace with a new lter.
Loading ...
Loading ...
Loading ...