Loading ...
Loading ...
Loading ...
11
5. Turn the collection tank upside down and insert the two caster feet into the slots and apply
pressure until they click into place (Fig. 4).
6. Insert the wheel axle into the rear wheel housing on the base. Insert a washer onto the axle
followed by the rear wheel and another washer. Insert the ‘R’ lock pin into the hole on the end
of the axle to lock into place. Snap the hub cap onto the wheel. Repeat the same steps on the
other end of the axle (Fig. 5).
7. Insert the handle into the slots located on the top of the power head and secure it with the
screws provided. Do not over-tighten the screws (Fig. 6).
<RXUYDFXXPFRPHVUHDG\IRUGU\YDFXXPFOHDQLQJ,IWKHFDUWULGJH¿OWHULVQRWLQVWDOOHGUHIHUWR
page 19 for installation instructions (Fig. 7 & 8).
2SWLRQDO)RULPSURYHGGXVW¿OWUDWLRQ¿WWKHGXVWEDJÀDQJHRQWRWKHLQOHWSRUWWDNLQJFDUHQRW
to damage the bag (Fig. 9).
NOTE: The dust collection bag is for dry pick-up only.
)RUZHWYDFXXPFOHDQLQJUHPRYHWKHFDUWULGJH¿OWHUDQGLQVWDOOWKHVXSSOLHGIRDPZHW¿OWHU
6HHSDJHIRUWKHIRDPZHW¿OWHULQVWDOODWLRQLQVWUXFWLRQV)LJ
11.Position the hose storage rack as illustrated. Squeeze the open sides of the hose storage rack
inward. Insert the hose storage rack into the channel on the front side of the power head just
above the top edge of the tank. Verify that the rack is secured in place as shown in (Fig. 11 &
12). Then squeeze in the other hose storage rack and insert it into the corresponding channel
making sure it is secured.
12.Place the power head back on the collection tank aligning the top section with the latches, and
snap into place (Fig. 13).
(QVXUHWKHHQGRIWKHFOHDQLQJVROXWLRQWXEHLVVHFXUHO\¿WWHGLQWRWKHFOHDQLQJVROXWLRQWDQN)LJ
14).
14.A cleaning solution delivery tube runs along the hose with a threaded connector at the end.
Insert the locking end of the hose into the vacuum port of the collection tank and turn clockwise
to lock into place. Connect the threaded connector on the end of the delivery tube onto the
cleaning solution outlet coupling on the front of the power head (Fig. 15).
15.Choose the desired accessory and/or the extension wand and connect it onto the remote-
FRQWUROKDQGOH)LJ7KHDLUÀRZUHJXODWLRQ
①
) on the remote-control handle allows you
to manually change the amount of vacuum suction (Fig. 17).
NOTE: ,IWKHVXFWLRQSRZHULVWRRKLJKZKHQFOHDQLQJDGMXVWWKHDLUÀRZUHJXODWLRQWRGHFUHDVH
the suction power (Fig. 17).
POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade wider than the
RWKHU7KLVSOXJZLOO¿WLQDSRODUL]HGRXWOHWRQO\RQHZD\,IWKHSOXJGRHVQRW¿WIXOO\LQWKHRXWOHW
UHYHUVHWKHSOXJ,ILWVWLOOGRHVQRW¿WFRQWDFWDTXDOL¿HGHOHFWULFLDQWRLQVWDOOWKHSURSHURXWOHW
Do not change the plug in any way. Double insulation eliminates the need for the three-wire
grounded power cord and grounded power supply system.
PROGRAMMING THE REMOTE-CONTROL HANDLE
NOTE: The programming of the remote-control handle has been preset and is ready to be used
in both vacuum and detergent mode. Reset the remote-control handle using the steps below if
unable to operate in vacuum mode.
1. Ensure the vacuum is plugged into the power outlet.
2. Switch the on/off switch to the “I” ON position.
3. Locate the detergent mode button on the power head indicated by the following symbol .
4. Press and hold the detergent mode button until the indicator light illuminates continuously
(Fig. 18).
5. While the light is on, press and hold the detergent mode button on the remote-control handle
XQWLOWKHLQGLFDWRUOLJKWRQWKHSRZHUKHDGVWDUWVWRÀDVK7KHUHPRWHFRQWUROKDQGOHLVQRZ
programmed to vacuum, and you should be able to operate in both detergent and vacuum
modes (Fig. 19).
,IWKHLQGLFDWRUOLJKWGRHVQRWÀDVKUHSHDWVWHSVWR
Loading ...
Loading ...
Loading ...