Loading ...
Loading ...
Loading ...
Follow lhe inslructions below to set the amplifier output
Io malch the size of your room and speakers. Press A / v
m cycle through parameters 1 through 4, and ( / > to alter
the parameler setting.
Factory default settings are highlighted.
(I) ROOM
Seltings: S, M, L
Select lhe size of the room you have installed your
speakers in. Roughly speaking, the room sizes are
defined as follows:
[U.S.A. and Canada modelsl
S: 16fi. x 3fL, 200sq.fl. (4.8 x 4m, 20m 2)
M: 20fi. x 16fi., 300sq.fi. (6.3 x 5.0m, 30mz)
L: 26ft. x 19fi., 450sq.fi. (7.9 x 5.8m, 45m z)
[Olher models]
S: 3.6m x 2.8m, 10m _
M: 4.8m x 4.0m, 20m _
L: 6.3m x 5.0m, 30m _
(2) SUBWOOFER
Sellings: YES, NONE
Select YES if you have a subwoofer in your system,
or NONE if you do not.
(2) SPEAKERS
Sellings: 2, 3, 4, 5, 6 (spk)
Select lhe number of speakers you wish to use in your
speaker configuralion. This number does not include
your subwoofer.
Setting Display Speaker
2spk _ @ Main L/Main R
3spk Main L/Center/Main R
4spk _1_ _1_ Main L/Main R/Rear L/
_ RearR
5spk Main L/Center/Main ILl/
_ Rear L/Rear R
6spk Main L/Center/Main ILl/
_1_ Rear L/Rear Center/Rear R
®
SET or CANCEL
Select SET to confirm the changes you made to the
above three settings. The unit will output a lest tone to
the speakers (see ®). Alternatively, select CANCEL
Io exit this menu without altering any of the unit
settings.
Use the test tone to check the speaker levels.
When you select SET in (4), the display changes to
"CHECK: Test'IBne', and lhe unit outputs a lest tone
Io each of the speakers in turn. When the test tone
begins, the display changes to "CHECK OK: YES".
If the volume of the test tone varies between speakers,
press ( / ) to change the display to "NO". The unit
will automatically enler the "2 SP LEVEL" mode.
If the test tone is output at lhe same volume from all
of lhe speakers, select "CHECK OK: YES". The unit
will exit from the SETUP menu.
• The unit cycles the test tone around each of the speakers in
turn twice.
• The indicator of the speaker currently outputting the test tone
flashes on the front panel display.
Use this menu to compare and adjust the test tone oulput
from each speaker to the output from the left main (or lefl
rear) speaker so lhal the volmne level for all speakers is
identical. Press/x / x/to select a speaker, then adjust the
balance using ( / ).
• The unit outputs the test tone from the selected speaker and
the left main (or lel_ rear) speaker in turn. The indicator of the
speaker currently outputting the test tone flashes on the front
panel display.
(I) L-R
Adjusts the balance between the main left and right
speakers.
(2) c
Adjusts the balance between the main left and center
speakers.
® RL
Adjusts the balance between the main left and rear
left speakers.
® RC
Adjusts the balance between the rear left and rear
center speakers.
® RR
Adjusts the balance between the rear left and rear
right speakers.
® SWFR
Adjust the balance between the main left speaker and
the subwoofer.
|
21
Loading ...
Loading ...
Loading ...