Loading ...
Loading ...
2
Operation
Unit start / stop
In HEAT mode,warm air will blow out after a short
periodof the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
Cooling only unit do not have displays and functions
related with heating
Display Board
Remote
Controller
Note
COOL
DRY
HEAT
FAN
nothing
In DRY mode, when room temperature becomes
lower than temp.setting+2
o
C,unit will run intermittently
at LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
automatically adjusts the fan speed
temperature.
When FAN is set to AUTO, the
according to room
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
Operation
Mode
AUTO
Press FAN button. For each press, fan speed
Remote controller:
Press
button
Every time the button is pressed, temp.setting
increase 1
o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
o
C,if kept depressed, it will
decrease rapidly
Select a desired temperature.
3.Fan speed selection
2.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
Press ON/OFF on the remote controller, unit starts.
/
Remote controller
changes as follows:
at air outlet if all vertical louvers are
right.
mode ,
controller will automatically
Note:
set swing position.
2
Remote controller
Air Flow Direction Adjustment
Press button again ,
vertical flap will stop over
present position,
the swing function will be cancelled
2.Press button. changes as follows: Pos.4
1.Vertical flap
Pos.1
Pos.2
Pos.3
3.Press
button to choose the Pos.2 and Pos.3.
Pos.4
Pos.5
(Autoswing)
COOL/DRY/AUTO(Initial state):
HEAT(Initial state):
(no)
LOW
MED HI
AUTO
Display
circulated
When restart after remote turning off, the remote
return to the previous
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
1
3
2
DRED Operation
Haier Peaksmart enabled air-conditioners have a Demand
Response Mode display on the indoor unit.
The display could be labelled d1, d2, d3 (wording may
differ model to model).
odottahWnoitpircseDyalpsiDedoM
DRM3 d3
Your air-conditioner will continue
to cool or heat during the peak
demand event. The energy
consumed by your air-conditioner
is capped to 75%.
No action is required.
DRM2 d2
Your air-conditioner will continue
to cool or heat during the peak
demand event. The energy
consumed by your air-conditioner
is capped to 50%.
No action is required.
DRM1 d1
Your air-conditioner is still turned
on and the fan will continue to
operate. Your compressor is
turned off and cool/hot air will no
longer be generated
DRM1 mode is only activated during
emergency demand management
situations. This mode will automatically reset
the device within 2 hours .If your air-con is in
this mode for longer than 2 hours please
contact Energex on 13 12 53.
(This function is unavailable on some models.)
These modes are described in more detail below:
Loading ...
Loading ...
Loading ...