WLG510WCLP USER MANUAL

Loading ...

8 9

INSTALLATION INSTALLATION

Service fuse location – Models with power point only

This product is fitted with a power outlet at each end of the

control panel� The outlets are protected by a replaceable 15

amp fuse located at the rear of the product�

WARNING

Before servicing the fuse, ensure that all power to the product

is switched off.

To access fuse, unscrew fuse housing and remove from

appliance� (See diagram)�

Fuse

Fuse housing

Electric wiring requirements

The cooker MUST be installed in compliance with:

• Wiring connections in AS/NZS3000 wiring rules�

• Local regulations, municipal building codes and other

statutory regulations�

• Data plate – Gives information about the rating and

is located behind the bottom of the oven door�

For New Zealand only: The cooking range must be connected

to the supply by a supply cord fitted with the appropriately

rated plug that is compatible with the socket-outlet fitted

to the final sub-circuit in the fixed wiring that is intended to

supply this cooking range.

• A functional switch MUST be provided near the appliance

in an accessible position (AS/NZS3000 – Clause 4�7�1)�

• Wiring MUST be protected against mechanical failure

(AS/NZS3000 – Clause 3�9)�

• The cooker requires a means of all pole disconnection

incorporated into the fixed wiring� This MUST have a

disconnection gap of 3mm�

• The cooker MUST be properly earthed�

• Disconnection in the fixed wiring must occur in

accordance with the AS/NZS3000 Wiring Rules

• If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard�

• This range must be connected with cable of 75°C

rating minimum�

• This product has passed the insulation resistance test after

manufacture� If the resistance reading is low at installation,

it is probably caused by moisture from the atmosphere

being absorbed by the elements after the range has been

produced� (Pass at 0�01MΩ AS/NZS 3000 Wiring Rules

Clause 8�3�6�2)�

WARNING

IMPORTANT

Before you cook in your new oven it is important that the

protective oils used in the manufacture of the product be

removed. Refer to ‘Before Operating your Appliance for the

First Time’ in the Using The Oven section.

Hard wiring

1� Remove rear panel�

2� Fit wires through hole at bottom centre using the

appropriate gland to protect insulation of wires from the

hole edge� Note that the secondary insulation of the wires

will probably need to be removed to fit through gland� If

the conduit to appliance is required to bend due to rear

wall an elbow may be required to achieve this�

3� Set the length of wiring from the gland to terminal block,

ensuring length is sufficient but not excessive�

4� Make connections to terminals and engage wires into

plastic clip� Cable tie as per diagram and secure plastic clip

with two long screws supplied�

5� Replace rear cover�

Cable tie

Plastic screw

securing points

Plastic clip

Gland

Rated power input

MODEL TOTAL kW A1 kW A2 kW

WLE524WC 10�0 4�2 5�8

WLE522WC 9�4 3�6 5�8

WLE530WCA 9�1 3�6 5�5

WLE543WC 9�7 4�1 5�6

WLE522WC 9�9 4�1 5�8

WLE532WC 9�6 4�1 5�5

Replacing the oven door

(to be done by qualified personnel only)

1� Hold door with both hands�

2� Locate both hinges into the frame slots at the

same time�

installation

Procedure to assemble the door

(to be done by

personnel only)

Procedure to assemble the door (to be done by qualied personnel only).

3. Open door fully and rotate

the stirrups away from you,

back to their original position.

1. Hold door with both

hands and locate both

hinges into the frame slots

at the same time.

Frame slot

Hinge

Notch

4. Close the door fully.

2. Ensure that the location notch drops into the

frame slot.

Care should be taken not to damage other

parts of the cooker.

Frame slot

Hinge

Notch

Frame slot

Hinge

Notch

1. Hold door with both hands.

2. L ocate both hinges into the frame slots at the

same time.

3. E nsure that the location notch drops into frame

slot. Care should be taken not to damage other

parts of the cooker.

4. O pen door fully and rotate stirrups away from

you back to their original position.

5. C lose the door fully.

Chef 540 Upright Cooker INSTALLATION 19

Notch

3� Ensure that the location notch drops into frame

slot� Care should be taken not to damage other

parts of the cooker�

Notch

Hinge

Frame slot

4� Open door fully and rotate stirrups away from

you back to their original position�

INSTALLATION

5� Close the door fully�

6� Carefully remove any protective plastic film to prevent

damage to the appliance�

Loading ...

USER MANUAL - Page 9