Loading ...
Loading ...
Loading ...
Starting - Priming the Engine
Please Note:- When starting the engine for the first 3. Follow instructions in the Use - starting and
time, till with oil and gasaiine as described above in the stopping section.
Oil and Gasoline section. Priming is usually 4. If engine fails to stad after three pulls of the pull cord,
unnecessary when restarting a warm en_ne. However, push primer bulb three times and repeat step 3.
coot weather may require priming to be repeated. Starting engine thereafter
Starting the engine for the first time 1. MOVe engine speed control to FAST %' position and
1. AdVance engine speed contr_ to FAST '+' as iUus_ted push primer bulb firmly three times before starting
in _e Use - starBng and st_pp_g seclton, engine. (if engine stopped because it ran out of fuel,
2. Push primer bulb (F) firmly five times, refuel engine - push primer bulb three times.
Use - Starting
G_a - Recoil Starter Gh-a - Drive Speed Conf_ol
Gh-b - Engine Speed Control
Starting & Stopping Royal 53S Intek.
Starting
1. Connect the spark plug lead.
2. Move the Engine Speed Control to the FAST %'
position before starting. (GI)
3. Pull the operator presence control (OPC) to release
the brake on the engine aqd the biade.(G2)
4. Pail the recoil starter fully towards you until you feel
the full resistance, return the handle slowly then pull
the handle firmly towards you to its full extent. (Gg)
and Stopping
5. After the engine has started, aiJow to run for 30
seconds before commencing to use.
Engaging the Drive
1. Forward drive is engaged and disengaged with the
Powerddve lever at the top of the h&qdJe (G4).
2. Drive speed can be altered with the drive speed
control. (Gh)
3. Releasing the Powerdrive Lever stops the
forward drive automatically.
Stopping
1. Release the powerddve lever.
2. Release the OPC lever.
Use - Mowing
Now to Mow
1. Always use the correct mowing position (H1).
2. Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions (H2).
3. Mow twice a week in the growing season, your lawn
will suffer if more than one third of its length is cut at
one time and this may also result in poor collestfon.
Cutting Height Adjustment
1. The height of cut is altered by pulling the
adjustment lever away from the location slots and
moving to the selected position {Hg).
Emptying the Grasscateher
1. Lift the safety flap (H4).
2. Remove the grasscatoher from the machine (Hh)
3. Empty grasscafcher.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height, will help reduce engine oveifoad
and will help prevent damage to your Jawnmower.
Using as a mulcher
1. Your lawnmower is supplied with a mulching plug (Jl).
2. Stop your lawnmower as described in Use - starting
and stopping, &qd disconnest the spark plug.
3. Lift safety flap. Slide mulching plug into rear
discharge chute. (J2)
4. Ensure mulching plug is securely fitted. (J3)
5. The mulching plug prevents grass from being
collected by blocking the collection chute on the
underside of the deck.
6. Ensure the safety flap is positioned correctly.
Cutting System (K)
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES.
Replace your metal blade after 50 hours mowing
or 2 years whichever is the sooner - regardless
of condition. If the blade is cracked or riamageri
replace it with a new one.
Removing the Blade
• Disconnect the spark plug lead.
t. Use wrench to loosen blade bolt by turning anti-
clockwise.
2. Remove the blade bolt, blade and spacer washer.
3. Inspect for damage and clean as necessary.
Fitting the Blade
1. Fit the blade to the machine with the sharp edges
pointing away from the machine.
2. Re-assemble blade bolt through blade and
spacer washer.
3. Hold firmly and tighten blade bolt firmly with a
wrench. Do not over tighten.
Maintenance
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
IMPORTANT
Never use water for cleaning your lawnmowe_ DO
not aiean with chemical, including gasoline, or
solvents = some can destroy critical plastic parts.
[]
Cleaning
• Disconnect the spark plug lead.
1. Remove grass from under the deck with a brush
(L1 and L2).
2. Using a soft brush - remove grass clippings from
the engine air intakes and exhaust (L3), cutting
height adjustment area. (L4), around the wheels
(Lh) and the grasscatcher (L6).
3. Wipe over the surface of your lawnmower with a
dry cloth.
Loading ...
Loading ...
Loading ...