Loading ...
Loading ...
Loading ...
26 27
OPERATION
Charging the battery pack
NOTE:
Remove the battery pack from the charger after it has been fully charged.
NOTE:
Battery should be fully charged before rst use.
NOTE:
Make sure the mains voltage is the same as the rating label which is located on the
charger.
1. Connect the charger to a power supply. The red LED will light up.
To insert the battery pack into the charger, align the raised ribs of the battery pack with the
grooves of the charger then push it in. (Fig. J)
2. The green LED light of the charger will ash continuously during normal charging.
3. After charging is complete, the charger light will turn to a solid green light.
Power indicator (Fig. K)
This Li-Ion battery pack is equipped with a power indicator which is used to show the battery
packs remaining charge. Press the power indicator button to check battery charge as below.
The LEDs will stay lit for approximately 4 seconds.
To obtain the best life from the battery
1. Never allow the battery to completely discharge before recharging. The battery pack
should be placed on the charger whenever the battery pack is noticeably running down
or the tool no longer performs a task it previously performed.
2. Avoid conducting short charges. Make sure that the battery is fully charged each time by
allowing the charger to complete its full charging cycle.
3. Avoid allowing loose items like screws or nails etc. to be stored with battery packs as
these or similar items can short battery packs and cause a re or explosion.
4. Always unplug the charger when not in use and store in a dry and secure place.
5. Avoid charging or storing your battery in temperatures below 5°C and above 45°C.
6. After use, allow the battery to pack to cool down for approximately 30 minutes before
attempting to recharge.
Filling bar and chain lubricant (Fig. I)
WARNING:
Do not smoke or bring any re or ame near the oil or the chain saw. Oil may spill
and cause a re.
NOTE:
The chain saw is not lled with oil at the time of purchase. It is essential to ll the tank
with oil before use.
The chain is automatically lubricated with chain oil (recomanded chain oil CD20W-50)
during operation.
1. Position the chain saw on its side with its oil tank cap facing towards.
2. Clean the cap as well as the area around and then turn it anti-clockwise to remove.
3. Carefully pour the specically designed oil into the tank until reaching the bottom of the
lter neck.
4. Wipe off any excessive oil and replace the cap.
NOTE:
With upright position, oil should ll the inspection window. When the oil is no longer
visible in the inspection window, stop use immediately and rell.
OPERATION
Inserting and removing the battery pack
NOTE:
Hold the tool and the battery pack rmly when installing or removing the battery pack.
Failure to hold the tool and the battery pack rmly may cause them to slip off your hands and
result in damage to the tool and battery pack, potentially causing a personal injury.
Insert the battery pack. (Fig. L)
To install the battery pack, align the tongue on the battery pack with the groove in the housing
and slip it into place. Always insert it all the way until it locks in place with a little click. If not,
it may accidentally fall out of the tool, causing injury to you or someone around you.
Remove the battery pack.
(Fig. M)
1. Press once release to transport position.
2. Press again full releases the battery
3. Pull out the battery pack.
NOTE:
Do not use force when installing the battery pack. If the battery pack does not slide in
easily, it is not being inserted correctly.
WARNING :
Verify that the switch is in the OFF position before inserting or removing the
battery pack.
WARNING :
Verify that the battery pack is removed and the switch is in the OFF position
before inspecting, adjusting or performing maintenance on any part of the chain saw.
Starting/stopping the chain saw
NOTE:
Before starting the chain saw, check for the oil level, saw teeth sharpness and
properly-working kickback brake handle. Besides, balanced footing and proper distance
away from the ground are needed.
To Start
1. Make sure the Chain brake lever is in the OFF position - pulled back towards the handle.
(Fig. N)
2. Grasp the front and rear handles rmly, using both hands.
3. Press down the lock-off button rst, then squeeze the trigger switch to start. (Fig. O)
Release the lockoff button and continue to squeeze the trigger for continued operation.
WARNING:
Do not attempt to start the saw when the saw chain is in a cut.
To Stop
1. Release the trigger switch.
2. Push the chain kickback brake handle forward to the brake position to engage the chain
brake (Fig. N).
WARNING:
Always remove the battery pack from the chain saw during work breaks and after
nishing work.
Loading ...
Loading ...
Loading ...