Loading ...
Loading ...
Loading ...
76
ALWAYS UNPLUG THE NUTRIBULLET WHEN CLEANING OR ASSEMBLING.
• NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE
DISHWASHER.
• RINSE BLADES (AND CUP) IMMEDIATELY AFTER USE TO PREVENT DEBRIS
FROM DRYING AND STICKING TO VESSELS – IF NECESSARY, USE A DISH
BRUSH TO LOOSEN ANY DEBRIS.
• HAND WASH ONLY WITH MILD DISH SOAP AND WARM WATER (NOT HOT).
• DRY IMMEDIATELY.
• FOR TOUGH DEBRIS, FILL THE CUP
½ FULL WITH ROOM TEMPERATURE
(NOT HOT), MILD SOAPY WATER. THEN, SIMPLY TWIST ON THE BLADE, POP
IT ON THE BASE AND GIVE IT A RUN FOR 30- 45 SECONDS. THIS WILL LOOSEN
THE STUCK INGREDIENTS, AND WITH A LIGHT SCRUB AND RINSE IN WARM
WATER, YOU’LL BE ALL DONE.
• DO NOT PUT THE BLADES IN THE DISHWASHER AS ELEVATED TEMPERATURES
CAN DAMAGE GASKETS. SIMPLY HAND WASH WITH WARM, MILD SOAPY
WATER.
• WHEN WASHING BLADE, DO NOT ATTEMPT TO REMOVE THE GASKET RING.
SIMPLY HAND WASH THE BLADES IN ROOM TEMPERATURE, MILD SOAPY
WATER. IF NECESSARY, USE A DISH BRUSH TO LOOSEN DEBRIS. IF DESIRED,
THE BLADE AND GASKET MAY BE FURTHER DISINFECTED BY RINSING IN A
10% DILUTED SOLUTION OF WHITE VINEGAR AND WATER OR USE LEMON
JUICE. ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE
THE BLADE CONFIGURATION AND CAUSE LEAKAGE.
• IF IN TIME, A GASKET BECOMES LOOSE OR DAMAGED WITH USE, PLEASE
CONTACT CUSTOMER SERVICE FOR A REPLACEMENT BLADE HOLDER AT
WWW.BULLETBRANDS.COM.AU OR
WWW.BULLETBRANDS.CO.NZ
BLADES AND CUPS ARE CONSUMABLE PARTS
AND WILL REQUIRE REPLACEMENT.
WE RECOMMEND 6 MONTHS ON BLADES AND
CUPS AS REQUIRED.
STUBBORN CLEANUP
If ingredients dry inside the NutriBullet, make your cleanup a snap by filling the cup
about
full with room temperature (not hot) soapy water and screw on the Blade.
Place the cup assembly on the NutriBullet, Power Base for about 20-30 seconds. This
will loosen the stuck ingredients, and with a light scrub and rinse in warm water,
you’ll be all done.
MAINTENANCE
For the most part the Power Base doesn’t really get dirty, but if you neglect
to twist the blade on to the cup tightly, liquids can leak out and get into the
base and activator buttons.
Here’s how to clean it up.
Step 1: The most important thing is to UNPLUG the Power Base before cleaning!
Step 2: Make sure the blade is not attached to the Power Base.
Step 3: Use a damp cloth to wipe down the inside and outside of the Power Base.
IN THE EVENT OF SPILL, CHECK THE UNDERSIDE OF THE BASE. IF LIQUID
FOOD IS EXITING THE VENTS, DO NOT USE UNTIL INSPECTED BY A CERTIFIED
ELECTRICIAN AS THE MOTOR HAS LIKELY BEEN COVERED IN FOOD, POTENTIALLY
GIVING USER AN ELECTRIC SHOCK.
Never put your hands or utensils near the moving blade and never use your hands
or utensils to press the activator buttons down while the Power Base is plugged in.
CLEANING
THE NUTRIBULLET
WARNING:
DO NOT WASH THE BLADES IN THE DISHWASHER. THE NUTRIBULLET
CUP AND BLADE SHOULD NOT BE IMMERSED IN BOILING WATER FOR ANY
REASON AS THIS WILL WARP THE PLASTIC AND DAMAGE THE
GASKETS.
Loading ...
Loading ...
Loading ...