Loading ...
Loading ...
Loading ...
If you experience
Dishes do not dry
completely
Noise
Spotting/Filming
Dishwasher does
not clean
completely
Dishwasher does
not drain
Recommended Solutions
NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous surface which tends to
collect water droplets. Towel drying may be necessary.
Use of rinse aid along with Heat Dry option is needed for proper drying.
Proper loading of items can affect drying.
Glasses and cups with concave bottoms hold water. This water may spill onto other items when unloading.
• Unload the bottom rack first.
• For improved results, place these items on the more slanted side of the rack.
NOTE: Common noises:
• Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.
• Normal water valve hissing may be heard periodically.
• A normal snap sound may be heard when the detergent dispenser opens during the cycle or when the door is opened
at the end of the cycle.
• Improper installation will affect noise levels.
Be sure the filters are properly installed.
A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms. Readjust the dishware
and resume the cycle.
Liquid rinse aid is necessary for drying and to reduce spotting.
Use the correct amount of detergent.
Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. Ifthe cloudiness disappears, it
is due to hard water. Adjust the amount of detergent and rinse aid (see "Dishwasher Care" section in full Use and Care
Guide). If it does not come clear, it is due to etching.
Be sure the incoming water temperature is set at 120°F (49°C).
Try using the High Temp and Sani Rinse options.
To remove spotting, run a vinegar rinse through the dishwasher.
• Wash and rinse the affected dishware and load into dishwasher. Remove all silverware and metal items. Put 2 cups
(500 mL) of white vinegar in a glass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option
turned off. No detergent is needed (see "Dishwasher Care" section in full Use and Care Guide).
Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing performance (see
Operating Your Dishwasher" section).
Check filter to ensure it is properly installed. Clean it if needed. (See "Filtration System" in full User Guide for details.)
Select the proper cycle for the type of soils. The Sensor Wash or the Heavy Wash cycles can be used for tougher loads.
Be sure the incoming water temperature is at least 120°F (49°C).
Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and hard water conditions.
Scrape food from dishes prior to loading (do not prerinse).
Iffoam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill
with water.
Suds can come from:
• Using the incorrect type of detergent, such laundry detergent, hand soap, or dish detergent for hand washing dishes.
• Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.
• Using an excessive amount of dishwasher detergent.
Be sure the cycle has been completed (the Clean light is on). If it has not, you will need to resume the cycle by closing the
door and pressing START/RESUME.
If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed from the disposer inlet.
Check for kinks in the drain hose.
Check for food obstructions inthe drain or disposer.
Check your house fuse or circuit breaker.
Whirlpool Corporation also offers a variety of accessories for your dishwasher. In the U.S.A., visit www.whirlpool.com/accessories to order. In
Canada, visit www.whirlpoolparts.ca to order.
Loading ...
Loading ...
Loading ...