Loading ...
Loading ...
Loading ...
OPTIONS CAN BE
SELECTED ADDED TIME
WITH WHAT IT DOES TO CYCLE
s
Target
Clean
IIIIII
HiTemp
Wash
Activates the TargetClean TM spray jets and provides
intensified water spray to back of lower level rack.
May add heat and time to cycle.
Raises main wash temperature to improve cleaning for
loads containing tough, baked-on food.
Sensor
Heavy
Normal
Soak & Clean
Sensor
Heavy
Normal
Soak & Clean
Raises main wash
temperature from
105°F (41°C)
to120°F (49°C).
Raises the main
wash temperature to
135°F (57°C)
0:12 to 0:57
0:05 to 0:13
ADDED
WATER
GALLONS
(LITERS)
0 to 4.8
(0 to 18.2)
0 to 3.86
(0 to 14.6)
[_ hold 3 sec
0
Sani
Rinse
m
Heat
Dry
m
Delay
hold 3 sec
am
®
Sani
Rinse
Sanitizes dishes and glassware in accordance with NSF
International NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments. The Sani
indicator indicates at the end of the cycle whether the Sani
Rinse option was successfully completed. If indicator does
not activate, it is probably due to cycle being interrupted.
Sensor
Heavy
Normal
Raises the main
wash temperature to
135°F (57°C) and
the final rinse
temperature to
156°F (69°C)
0:05 to 1:06
Dries dishes with heat. This option, with the use of rinse
aid, will provide the best drying performance. Plastic items
are less likely to deform when loaded in the top rack. Use
Heat Dry for optimum dry performance, Turn the Heat Dry
option off for air dry.
Sensor
Heavy
Normal
Soak & Clean
Uses heating
element to speed
drying times. Heat
Dry option defaults
to On when any
cycle is selected
except for 1- Hour
Wash.
0:08 to 0:46
0 to 3.86
(0 to 14.6)
Runs dishwasher at a later time. Select a wash cycle and
options. Each time you press the delay button it will display
the next available delay time. Press DELAY. Press START/
RESUME. Close door firmly.
NOTE: The dishwasher remembers the last Delay you
selected. To reset the delay time to something other than
what is displayed, continue to press the Delay button until
the desired delay time is reached.
NOTE: Anytime the door is opened (such as, to add a
dish); START/RESUME must be pressed again to resume
delay countdown.
Available Delays start of a
with any cycle up to 24 hours.
cycle
0:00
Avoids unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
Toturn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock light will
stay on for a short time, indicating that it is activated, and all buttons are disabled. Ifyou press any button while your dishwasher is
locked, light flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked.
To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off.
NOTE: If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate whether
Control Lock is active or not.
Control
Start
Resume
mini
Cancel/Drain
hold 3 sec
I
Purpose Comments
Press to start or
resume a wash
cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
flashes. Cycle will not resume until door is closed and START/RESUME is pressed.
NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3 seconds
of pressing START/RESUME. If door is not closed within 3 seconds, Start/Resume button LED
will flash, an audible tone will be heard (on some top control models), and cycle will not start.
Press to cancel
wash cycle.
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher drain
completely. Press and hold START/RESUME for 3 seconds.
To follow progress
of your
dishwasher cycle.
NOTE: Indicators
shown are not
available on all
models.
The Clean indicator glows when a cycle is finished.
If you select Sani Rinse option, when cycle is finished, the "Sanitized" indicator glows. If your
dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted, or water could not be heated to required temperature. The
light goes off when you open and close door or press CANCEL.
Loading ...
Loading ...
Loading ...