Loading ...
Loading ...
Loading ...
NSF Certified Temperature Gauge
This appliance is equipped with an NSF certified temperature
gauge to display cabinet internal temperature. The temperature
gauge is located on the top right side of the evaporator housing
inside the unit.
scratch the appliance surface when removing adhesive labels.
Any glue left from the tape can be removed with a mixture of
warm water and mild detergent or touch the residue with the
sticky side of tape already removed. DO NOT REMOVE THE
SERIAL PLATE.
Condensate Pan
Some models have a condensate pan in a fixed position located
behind the toe grill. This must not be removed from under the
cabinet. If the pan is removed, condensate will drop onto the
floor.
POWER FAILURE
DO NOT open the appliance lid unnecessarily if the
appliance is off for several hours.
Fluorescent Lamp (Glass Door Models)
The Glass Door Refrigerator is equipped with a 17 watt
fluorescent lamp. A ballast - lamp mismatch may result in poor
or no lighting.
If a power failure occurs, pack seven or eight pounds of dry ice
into the appliance every 24 hours. Look in the Yellow Pages
under "Dry Ice", "Dairies", or "Ice Cream Manufacturers" for local
dry ice suppliers. Always wear gloves and use caution when
handling dry ice.
If the lamp fails, replace with a lamp of the same type and
wattage. Also, replace a lamp that flickers continuously. This
could damage the ballast.
Turning the light off, when not in use, will save energy. However,
frequent ON-OFF cycling will reduce the lamp life.
Use only NSF certified lamp which can be ordered from your
Frigidaire Commercial Service Center by calling 1-866-738-1640.
Interior Light (Stainless Steel Door Models)
The Stainless Steel Door models are equipped with a 40 watt
bulb that lights up when the door is opened. If the bulb goes
bad, replace with bulb of the same type and wattage. This is a
special bulb with a shatterproof coating. Use only an NSF certified
bulb of the same type and wattage which can be ordered from
your Frigidaire Commercial Service Center by calling 1-866-738-
1640.
Other Features
• NSF Certified top mounted evaporator.
• 2 ½ thick urethane foam cabinet insulation.
• Torsion spring door closer (Glass Door models).
• Stainless steel evaporator housing.
• Removable stainless steel drain cover.
• Heavy duty front grill.
• Heavy duty commercially rated electrical harness.
• Heavy duty removable stainless steel shelf supports.
Routine Maintenance
Cleaning the Interior
Be sure to turn the temperature control to "OFF" and unplug the
electrical cord. Wash the inside surface of the storage area with
warm water and baking soda solution (about one tablespoon of
baking soda per quart of warm water). Rinse thoroughly with
clean, warm water and wipe dry.
Cleaning the Exterior
Wipe the cabinet exterior occasionally with a cloth dampened in
mild detergent and water. Rinse and wipe dry with a soft cloth.
Do not use razor blades or other sharp instruments that can
Energy Conservation Measures
This appliance is designed for efficiency with heavy foam
insulation. However, there are things that the user can do to
maintain the appliance in operating condition.
• Do not operate the appliance any colder than necessary to
maintain safe, product storage temperatures.
• Make sure the appliance is located to prevent direct exposure
to sunlight, air ducts, etc.
• Keep the door closed except for normal use. Inspect the door
often to see that it self-closes and the gaskets are in good
condition.
• Do not overstock the product in the cabinet because it will
block the normal air flow.
• Have at least annual inspections by a qualified service
company to see that the refrigerant charge is correct.
• This appliance operates more efficiently in a cooler ambient
than in a hot ambient. Try to maintain an ambient below 80°F
(27°C) and 65% RH (Relative Humidity) for maximum efficiency.
Periods of Non-use and Moving Tips
Leave the appliance operating during periods of non-use of less
than three (3) weeks.
Long Periods of Non-use
If the appliance will not be used for several months:
• Remove all food and unplug the power cord.
• Clean and dry the interior thoroughly.
• Leave the appliance door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
Moving
When moving the appliance, follow these guidelines to prevent
damage:
• Disconnect the power cord plug from the wall outlet.
• Remove foods, then defrost, and clean the appliance .
• Secure all loose items such as base panel, baskets, and
shelves by taping them securely in place to prevent damage.
• In the moving vehicle, secure appliance in an upright position
to prevent movement. Also, protect outside of appliance with
a blanket or similar item.
Loading ...
Loading ...
Loading ...