Loading ...
Loading ...
Loading ...
13
Making settings
Cleaning takes approximately one hour.
1. Set the function selector to < 3D hot air.
2. Set the temperature selector to s.
3. Press theu button.
The
u symbol lights up in the display. The time at which the
cleaning will end appears and the
p symbol is in brackets.
Cleaning will start after a few seconds. You will see the time
counting down and the
r symbol will be in brackets. The p
symbol goes out.
Cleaning is finished
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the
0 button twice and turn the function selector
to the off position. The oven switches off.
Cancelling cleaning
Press the
u button and turn the function selector to the off
position. The oven switches off.
Setting a later end time
You can delay the time at which the cleaning programme is due
to finish. For instance, you can set the cleaning programme to
run at night so that you can use your oven during the day.
Make the settings as described in steps 1 to 3. Before cleaning
starts, use the
@ or A button to set a later end time.
The oven switches to standby. The display shows the time at
which the cleaning will finish and the
p symbol is in brackets.
When cleaning starts, you can see the time counting down in
the display and the
r symbol is in brackets. The p symbol
goes out.
After cleaning
When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
■ Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
■ Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■ Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong type of cleaning agent, observe the information in the
table. Do not use
■ harsh or abrasive cleaning agents,
■ cleaning agents with a high concentration of alcohol,
■ hard scouring pads or sponges,
■ high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Cleaning the self-cleaning surfaces in the cooking
compartment
The back wall, ceiling and side walls of the cooking
compartment are coated with a highly porous ceramic layer.
This coating absorbs and disintegrates splashes from baking
and roasting while the oven is in operation. The higher the
temperature and the longer the oven is in operation, the better
the result will be.
Never treat the self-cleaning surfaces with oven cleaner.
If the self-cleaning surfaces no longer clean sufficiently, they
can be regenerated with the cleaning system. For more
information, please see the Cleaning system section.
Light discolouration of the coating does not affect automatic
self-cleaning.
Caution!
■ Never use abrasive cleaning agents. You will scratch or
destroy the highly porous coating.
■ Never treat the ceramic coating with oven cleaner. If oven
cleaner accidentally gets onto it, remove it immediately with a
sponge and plenty of water.
Area Cleaning agents
Control panel Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or glass
scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove traces of limescale, grease,
starch and albumin (e.g. egg white) immedi-
ately. Corrosion can form under such resi-
dues.
Special stainless steel cleaning products
suitable for hot surfaces are available from
our after-sales service or from specialist
retailers. Apply a very thin layer of the
cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Glass cover for
the oven light
Hot soapy water:
Clean with a dish cloth.
Seal
Do not remove.
Hot soapy water:
Clean with a dish cloth. Do not scour.
Rails Hot soapy water:
Soak and clean with a dish cloth or brush.
Telescopic
shelves
Hot soapy water:
Clean with a dish cloth or a brush.
Do not remove the lubricant while the pull-
out rails are pulled out – it is best to clean
them when they are inserted. Do not soak
or clean in the dishwasher.
Accessories Hot soapy water:
Soak and clean with a dish cloth or brush.
Area Cleaning agents
Loading ...
Loading ...
Loading ...