Loading ...
Loading ...
Loading ...
6
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety before you attempt to assemble or
operate your new lawn mower.
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
Your new lawn mower has been as sem bled at the factory with the exception of those parts
left unassembled for shipping pur pos es. To ensure safe and proper op er a tion of your lawn
mower, all parts and hard ware you assemble must be tight ened securely. Use the correct
tools as nec es sary to ensure proper tightness. All parts such as nuts, wash ers, bolts, etc.,
nec es sary to complete the as sem bly have been placed in the parts bag.
TO ASSEMBLE GRASS CATCH ER
1. Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be
used as a mulcher. To convert mower to
bagging or discharging, see “TO CON-
VERT MOWER” in the Operation section
of this manual.
Frame
handle
Frame
opening
Vinyl
bindings
MOWING
POSITION
Lower handle
LIFT
UP
Operator
presence
control bar
Upper
handle
LIFT
UP
Handle
knob
TO REMOVE MOWER FROM CARTON
1. Remove loose parts included with mower.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials except
padding be tween upper and lower
handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and
check carton thor ough ly for additional
loose parts.
HOW TO SET UP YOUR MOW ER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage con trol cables.
1. Raise handles until lower handle sec-
tion locks into place in mowing position.
2. Remove protective padding, raise up-
per handle sec tion into place on lower
handle and tighten both handle knobs.
3. Remove handle padding holding operator
pres ence control bar to upper handle.
Your lawn mower handle can be adjusted
for your mowing comfort. Refer to “AD-
JUST HANDLE” in the Service and Adjust-
ments section of this manual.
39
CRAFTSMAN ROTARY LAWN MOWER - - MODEL NUMBER 917.376152
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
1 400292 Drive Control Assembly (Includes Cable)
3 175262 Pan Head Tapping Screw #10-24 x 2-3/4
4 199687 Screw, Hex Washer Head
5 196857 V-Belt
6 194185X428 Bar, Drive Control
7 191730 Nut, Hex, Flangelock
9 83923 Locknut, Hex
11 193912X460 Wheel & Tire Assembly, Front
12 12000058 E-Ring
13 750003 Pinion
14 189403 Dust Cover
15 191017 Pawl, Drive
16 67725 Washer, Flat 3/8
17 191039 Bearing, Wheel Adjuster
18 701037 Selector Knob
23 88652 Screw
24 191730 Nut, Hex, Flangelock
25 197163X479 Belt Guide Bracket
26 192325 Screw
28 194407X428 Drive Cover
32 194018 Drive Pulley
35 195110 Kit, Wheel Adjuster, LH
(Includes Knob and Bearing)
36 191636 Gear Case Assembly, Complete
38 73800400 Locknut 1/4-20
40 192849 Spring
41 195107 Kit, Wheel Adjuster, RH
(Includes Knob and Bearing)
54 403035 Grassbag Assembly
55 86012 Driveshaft Cover
57 189680 Frame, Grassbag
61 196886 Case, Upper
62 197057 Shaft, Output
63 183508 Seal, Output Shaft
64 183511 Bushing
65 183509 Washer
66 183514 Seal, Worm Shaft
67 183506 Bearing, Ball
68 183499 Gear, 27 Teeth
69 196884 Fixed Dog Clutch
70 183505 Wireform
71 196883 Movable Dog Clutch
72 196882 Fork
73 183513 Screw, Case
74 196881 Case, Lower
75 196880 Seal, Lever
76 196879 Lever
77 196878 Screw, Lever
78 196877 Spring
79 183502 Shaft, Worm
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.
Loading ...
Loading ...
Loading ...