Loading ...
Loading ...
Loading ...
14 | English
The inflation adapters(23) can also be put on the curved
nozzle(20).
Fitting the vacuum hose
Extraction Function (seefigureF)
Push the vacuum hose(22) into the hose connection
piece(2) and turn it as far as possible in the direction of ro-
tation .
Blowing Function (seefigureG)
Put the vacuum hose into the rear hose adapter(12) and
turn it all the way in the rotational direction .
Replacing/Inserting Dust Bag (seefigureH)
(accessories)
Open the catches(10) and remove the top part of the dust
extractor(9).
Remove the dust bag holder(24).
Put the dust bag(25) on the dust bag holder(24) and insert
the dust bag(25) with the dust bag holder(24) into the
container(1).
Put the top part of the dust extractor(9) back on and con-
nect the container(1) with the top part of the dust
extractor(9) by closing the catches(10).
Changing the Main Filter (see figure I)
Note: When replacing the filter, make sure that no dust gets
into the motor housing.
Press the fixing lever of the filter holder(28) towards the
main filter(29) and remove the filter holder(27) with the fil-
ter. Remove the filter(29) from the filter holder(27).
To insert a new filter, place the filter(29) with the filter
folds down into the filter holder(27). Insert the filter
holder(27) with the filter(29) into the top part of the dust
extractor(9).
Attaching the Vacuum Hose to the Dust
Extractor (seefigureJ)
Wrap the fitted vacuum hose(22) around the dust extractor.
Pull up the retaining strap(7) and hook it into the holder.
Operation
Starting Operation
u Before extraction, ensure that the filter unit is se-
curely fitted.
u Do not use damaged filters (e.g. no cracks, small
holes, etc.). Replace any damaged filters immedi-
ately.
Switching On and Off
To switch on the dust extractor, press the on/off button(5).
Press the ECO button(4) to extend the rechargeable battery
runtime.
To switch off the dust extractor, press the on/off button(5)
again.
ECO Mode
When ECO mode is activated, the suction power is reduced
in order to increase battery runtime(see "Technical data",
page12).
Dry Extraction
Use a dust bag for dry extraction if possible (accessories).
If the dust bag is full, replace it with a new dust bag.
u Check the dust bag each time after using.
Extracting Dust that Accumulates from Working Power
Tools (seefigureL)
u There must be a sufficient air exchange rate (L) in the
room when the exhaust air comes back into the room.
Be aware of the corresponding national regulations.
Fit the universal adapter(21).
Insert the universal adapter(21) into the extraction outlet of
the power tool.
Note: When working with power tools that have a low air
feed into the vacuum hose (e.g. jigsaws, sanders, etc.), the
false air intake(31) of the universal adapter(21) must be
opened. This will improve the total output of the dust ex-
tractor and the power tool. To do this, turn the ring above
the false air intake(31) until the opening is at its maximum
size.
Wet Extraction
u The vacuum cleaner must not be used as a water
pump. The vacuum cleaner is designed for vacuuming air
and vacuuming water mixtures.
Steps to Take before Wet Extraction
Empty and clean the container(1). A dust bag(25) must not
be used.
Clean the fill level sensors(30) using a soft cloth (see
figureI).
Fit a suitable nozzle.
Vacuuming up Liquids
Switch on the dust extractor using the on/off button(5).
The dust extractor is equipped with fill level sensors(30)
(see figureJ). The dust extractor shuts down if the maximum
fill level has been reached.
Note: When extracting non-conductive liquids (e.g. drilling
emulsion, oils and fats), the dust extractor will not switch off
when the container is full. The fill level must be constantly
monitored and the container emptied in good time.
Steps to Take after Wet Extraction
Empty the container(1).
To avoid mould formation, remove the top part of the dust
extractor(9), open the filter holder(27), take out the
filter(29) and let everything dry well.
1 609 92A 62Y | (04.05.2021) Bosch Power Tools
Loading ...
Loading ...
Loading ...