CT6K01(11)
6MQA4511-01
En
Procedure for Pairing for the First Time (for Android Users)
Here, pairing refers to the setting used to connect the camera and smartphone or tablet (below, “smart device”)
through Bluetooth.
Parts of the Camera
Movie button
Photo button
Status lamps
Power-on lamp Airplane mode switch N-Mark
Before Pairing
Camera
• Press and hold the movie button on the camera for about 3 seconds to turn it o. When the camera turns o,
the power-on lamp turns o.
• Use a suciently charged battery so that the camera does not turn o during the procedure.
• Turn o the airplane mode switch on the camera.
• Insert a microSD memory card with sucient free space into the camera.
- Use microSDXC memory cards with a UHS Speed Class rating of 3 or faster when recording movies at an image
size/frame rate of 2160/24p (4K UHD) or 1920/24p.
• Disconnect the HDMI cable or USB cable.
Smart device
• Two types of apps are available: “SnapBridge” and “SnapBridge 360/170”. Use “SnapBridge
360/170” when pairing with the KeyMission 360.
• Do not pair from the Bluetooth setting screen of the smart device.
Pairing Procedure (without NFC)
1 Make sure that the camera is o (the power-on lamp is o ).
2 Enable Bluetooth and Wi-Fi on the smart device.
• Do not pair from the Bluetooth setting screen of the smart device.
3 Install and start the SnapBridge 360/170 app.
4 Press the movie button or photo button on the camera to put it into pairing standby mode.
• When the status lamps ash green at the same time for a while and then alternately ash green, the camera
enters pairing standby mode.
• If the camera remains in pairing standby mode for about 4 minutes, it turns o (the power-on lamp turns o )
automatically. If the camera turns o during the pairing procedure, press the movie button or photo button
on the camera to put it into pairing standby mode.
* If the camera does not enter pairing standby mode even after pressing the movie button or photo button,
press and hold the movie button for about 7 seconds while the camera is o.
5 When the screen shown on the right is displayed, tap the camera name.
Connect to Camera
Camera name
KeyMission 360_xxxxxxxx
• If pairing is successful, the screen shown on the right is displayed. Follow the on-screen
instructions.
Connect to Camera
Connected to KeyMission 360_xxxxxxxx
Pairing Procedure (with NFC)
1 Make sure that the camera is o (the power-on lamp is o ).
2 Enable Bluetooth, Wi-Fi, and NFC on the smart device.
• Do not pair from the Bluetooth setting screen of the smart device.
3 Install the SnapBridge 360/170 app.
4 Close all apps that use NFC, including the SnapBridge 360/170 app.
• Pairing may fail if apps that use NFC are running.
5 Press the movie button or photo button on the camera to put it into pairing standby mode.
• When the status lamps ash green at the same time for a while and then alternately ash green, the camera
enters pairing standby mode.
• If the camera remains in pairing standby mode for about 4 minutes, it turns o (the power-on lamp turns o )
automatically. If the camera turns o during the pairing procedure, press the movie button or photo button
on the camera to put it into pairing standby mode.
* If the camera does not enter pairing standby mode even after pressing the movie button or photo button,
press and hold the movie button for about 7 seconds while the camera is o.
6 Tap the NFC antenna of the smart device to the Y (N-Mark) on the camera.
• The SnapBridge 360/170 app starts. When Camera name acquired. Connect? is displayed,
select OK. If pairing is successful, the screen shown on the right is displayed.
Connect
When You Cannot Pair
Perform the following and then pair again by proceeding to “Pairing Procedure (without NFC)” or “Pairing
Procedure (with NFC)”.
• Press and hold the movie button on the camera for about 3 seconds to turn it o (when the camera turns o,
the power-on lamp turns o ).
• Close the SnapBridge 360/170 app.
Auto O
By default, if the camera is not operated for about 30 seconds, the camera turns o automatically. We recommend
that Auto o is set to 5 min until you are comfortable with operating the camera and app (set in Camera M
Camera settings M Auto o in the app).
To Learn More About Using the SnapBridge 360/170 App
See the online help (tap Other M Info/settings M Instructions in the app).
