Loading ...
Loading ...
Loading ...
Connecting the Water u ply 13
WARNING
To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator
from electrical power before connecting a water
supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainiees Steel braided tubing is
recommended for the water supply line. Water
supply tubing made of 1Ainch plastic is not
recommended to be used. Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer will not be responsible for any
damage if plastic tubing is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker, if the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need:
,, Basic Tools: adjustable wrench, flat-blade
screwdriver, and Phillips TM screwdriver
- Access to a household cold water line with water
pressure between 30 and 100 psi.
,, A water supply line made of ¼ inch (6.4 mm) OD,
copper or stainless steel tubing.To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
,, A shutoff valve to connect the water supply line
to your household water system. DO NOT use a
self-piercing type shutoff valve.
,, A compression nut and ferrule (sleeve)br connecting
a copper water supply line to the ice maker inlet valve.
NOTE
Check with your local buildingauthority for
recommendations on water linesand associated materials
prior to installingyour new refrigerator. Depending on
your local/state buildingcodes, Electrolux recommends for
homes with existing valves its Smart Choice@water linekit
5305513409 (with a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Electrolux recommends
itsSmart Choice water_ line kit 5305510264 (with a 20 ft.
Copper Water Line with self-tapping saddle valve). Please
refer to www.frigidaire.corrVstorefor more information.
To Connect Water Supply Line To tee Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket.
Turn ON water supply and flush supply line until
water is clear.Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line. Push
water supply line into water valve inlet as far as it will
go (¼ inch / 6.4 mm). Slide ferrule (sleeve) into valve
inlet and finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use stainless steel tubing -The nut and
ferrule are already assembled on the tubing. Slide
compression nut onto valve inlet and finger tighten
compression nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See Figure 2.
5. Wilh sleelclampand screw,securewatersupplyline
(copperlubingonly)to rearpanelof refrigerabras shovm.
6. Coil excess water supply line (copper tubing
only), about 2V2 turns, behind refrigerator as
shown and arrange coils so they do not vibrate or
wear again st any other surface.
7. Turn ON water supply at shutoff valve and tighten
any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (side
mounted) or set the ice maker's On/Off power
switch to the "!" position (rear mounted).
Figure 1
iMPORTANT
Figure 2
After connecting the water supply, refer to "How to Prime
the Water Supply System" for important information
about priming an empty 'water supply system.
Your refrigerator's water supply system includes
several tubing lines, a water filter, a water valve, and
a water tank_ To ensure that your water dispenser
works properly, this system must be completely
filled with water when your refrigerator is first
connected to the household water supply line.
Loading ...
Loading ...
Loading ...