Loading ...
Loading ...
Loading ...
Troubleshooting
PROBLEM
EngineWill Not Start Using
Recoil Starter
EngineStalls or Stops After
Running
Engine LosesPower
ExcessiveVibration
IVlowerWillNotIVloveLoss
OfTraction
Cutting Grass Improperly
Poor GrassDischarge
Oil Leaking
PROBABLECAUSE
1.Fueltank empty•
__.Engine needschoking•
3.Spark plug wire disconnected•
1.Fuelshut-oft in the 'otr position.
1.Bladecontrol is releasedor is not being held
securelyagainst handle•
?..Enginespeed control in 'Choke' position.
3.Fueltank empty.
1.Engineair pre-cleanerand or air cleaner dirty.
3.Spark plug detective or gapset improperly.
5.Water,debris or stale fuel in fuel system.
L Fuelshut-off in the 'otr position.
1.Engineair pre-cleaneror air cleaner dirty.
?_.Spark plug faulty.
3.Water,debris or stale fuel in fuel system.
• Damaged,out of balanceor bent mower blade.
__.Loose bladecomponents.
:I.Loose or missing air lift (it equipped).
1.Lumpy or frayed belt.
1.Build-up of debris on or around wheel drive
.'omponents.
__.Driven disc slipping.
3.Drive belt requires replacement.
1.Damagedtransmission.
1.Cutting height too low or high.
__.Enginespeedtoo slow.
3.Forward ground speedtoo fast.
1. lerraced cut, side to side.
5.Excessivedeck pitch, front to rear.
5.Cutting bladedull or damaged.
1.Enginespeedtoo fast.
__.Forward speedtoo fast.
3.Grass is wet.
1.Excessivelyworn or damaged blade.
3.Build up of grass clippings and debris under deck.
5.Improper bladeinstalled on deck.
L Bladeinstalled improperly on deck.
1.Leaking engine case.
CORRECTIVEACTION
• Fill tuel tank with tresh fuel.
__.Chokeengine. Check EngineManual tor Instructions.
3.Placespark plug wire onto spark plug.
1. lurn Fuelshut-off to 'On' position.
• Bladecontrol should be heldsecurely against handle
tt all times during operation of mower.
_Llurn oft choke.
3.Fill with tuel to proper level.
1.Cleantree of all debris.
3.Servicespark plug.
5.Drain and cleantuel system.
7. lurn Fuelshut-off to 'On' position.
1.Cleanor replacetilters.
__.Servicespark plug.
3.Drain and cleantuel system.
1.Service mower blade.
__.Serviceand tighten loose parts.
:I.Replaceair lifts, lighten to proper torque.
1.Heplacebelt.
• Cleandebris.
_LCleanor replacedriven disc•
:LHeplacedrive belt.
1.Contactauthorized SNAPPERdealer.
•Adjust cutting height.
__•Move engine speedcontrol to 'Fast' position.
3.Move ground speedcontrol to a slower speed.
1•Adjust height of cut with height adjust levers.
3.Adjust height of cut with height adjust levers.
5.Sharpen cutting edgesor replace blade.
1.Move engine speedcontrol to 'Fast' position.
__•Move ground speedcontrol to a slower speed.
3•Mow when grass is dry•
1•Service mower blade.
3.Cleandeck.
3.Install proper SNAPPERblade.
7.Install bladeproperly.
• Contactauthorized SNAPPERdealer.
__.Checkand tighten drain plug.
:LMakesure dip stick or oil tiller cap is securely in
31ace.
=3"
1-,1-
-'I
21
Loading ...
Loading ...
Loading ...