Loading ...
Loading ...
Loading ...
"If yoursawis for useon lessthan 150 volts it has a plug
that looks like below.
3-PRONG PLUG
\
GROUNDING PRONG
PROPERLY GROUNDED
3-PRONG OUTLET
If the outlet you are planning to use for this saw is of the
two prong type DO NOT REMOVE OR ALTER THE
GROUNDING PRONG IN ANY MANNER. Usean adapter
as shown and always connect the groundi.g lug to a known
ground.
It is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE 10rongoutlet.
An adapter asshown below is available for conne_ing plugs
to 2-prong receptacles, The green grounding lug extending
from the adapter must be connected to a permanent ground
such asto a properly grounded outlet box.
Plug power cord into 110-120V properly grounded type
outlet protected by a 1S-amp. time delay or Circuit-Saver
fuse or circuit breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY A
QUALI FlED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUG WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET,
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS: IN PROXIMITY TO
PLUMBING, OR OUT OF DOORS. IF AN ELECTRICAL
SHOCK OCCURS THERE IS THE POTENTIAL OF A
SECONDARY HAZARD SUCH AS YOUR HANDS
CONTACTING THE SAWBLADE.
This saw is equipped with a 3_conductor cord and
grounding type plug which hasa grounding prong, approved
by Underwriters' Laboratories and the Canadian Standards
Association, The ground conductor has a green lug and is
attached to the toot housing at one end and to the ground
prong in the attachment plug at the other end.
This plug requires a mating 3-conductor grounded type
outlet asshown.
GROUNDING LUG
ADAPTER
\
MAKE SURE THiS iS
3-PRONG CONNECTED TO A
PLUG KNOWN GROUND
2-PRONG
RECEPTACLE
NOTE: The adapter illustrated {sfor use only if you already
have a properly grounded 2-prong receptacle.
The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent
over-heating and motor burn-out, use the table below to
determine the minimum wire size (A.W.G.) extension cord.
Use only 3 wire extension cords which have 3 prong
grounding type plugs and 3-pole receptacles which w_ll
accept the plug on the saw.
Extension Cord Length Wire Size A,W.G.
Upto 100 Ft...................... 12
100 - 200 Ft....................... 10
200 - 400 Ft ......................... 8
CONTENTS
WARRANTY ................................. 2
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS ................. _....... 2
ADDITIONAL SAFETY INSTRUCTIONS
FOR TABLE SAWS ........................... 3
MOTOR SPECIFiCATiONS AND ELECTRICAL
REQUIREMENTS ............................ 4
UNPACKING AND CHECKING CONTENTS ........ 6
Tools Needed ................................ 6
List of Loose Parts ............................ 6
ASSEMBLY .................................. 7
Installing Elevation and Tilt Handwheels ........... 7
Checking Table Insert ......................... 7
Checking Blade Squareness to Table .............. 8
Checking Blade Elevation ...................... 8
Attaching Table Extensions ..................... 8
Installing Rip Fence Guide Bars .................. g
Assembling Steel Legs ........................ 10
Mounting Saw .............................. 10
Aligning Table Extensions ..................... 11
Aligning Rip Fence .......................... If
Installing Blade Guard ........................ 13
GETTING TO KNOW YOUR SAW ............... 15
On-OffSwltah .............................. 15
Reset Button ............................... 16
Elevation Handwheel ......................... 16
Tilt Handwheel ............................. 16
Rip Fence ................................. 16
Miter Gauge ................................ 16
Blade Guard ................................ 16
Table Insert ................................ 16
Removingand InstallingSawblade ............... 17
BASIC SAW OPERATION USING THE MITER GAUGE 17
Work Helpers ............................... 17
Crosscutting ................................ 18
Repetitive Cutting ........................... lg
Miter Cutting ............................... 20
Bevel Crosscutting ........................... 20
Compound Miter Cutting ...................... 2(]
BASIC SAW OPERATION USING THE RIP FENCE .. 20
Ripping ................................... 21
Bevel Ripping .............................. 21
Rasaw_ng .................................. 22
Cutting Panels .............................. 23
Rabbeting ................................. 23
ADJUSTMENTS .............................. 23
Miter Gauge ................................ 23
Heeling Adjustment or Parallelism of
Sawblade to Miter Gauge Groove ............... 24
Blade Tilt, or Squareness of
Blade to Table ............................. 2,$
Blade Elevation ............................. 26
Tilt and Elevation Mechanism .................. 26
MAINTENANCE ............................. 26
LUBRICATION .............................. 2'7
RECOMMENDED ACCESSORIES ................ 27
TROUBLE SHOOTING ........................ 2,g
REPAIR PARTS .............................. 30
Loading ...
Loading ...
Loading ...