Loading ...
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or
workmanship, Sears will repair it. free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES,
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state,
SEARS. ROEBUCK AND CO.. Sears Tower. BSC 41-3. Chicago, ]L 60664
general safety instructions for power tools
1. KNOW YOUR POWER TOOL
Read the owner's manual carefull,_. Learn ts
aoDlication and limitations as well as the specific
potenttal hazards peculiar to this tool
13.
2. GROUND ALL TOOLS
Th ; tool s equipped with an approved 3*conductor
coro and a 3*prong grounding tvoe plug Io fit the 14.
Drouer grounamg [yDe receptacle. The green conauctot
'n me cord _s the grounding w_re. Never connect the
green wire to a live terminal 15.
adjustment and
3. KEEP GUARDS IN PLACE
n working order, and n proper
alignment.
4. REMOVE ADJUSTING KEYS
AND WRENCHES
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on,
5. KEEP WORK AREA CLEAN
Cluttered areas and benches mvite accidents. Floor
must not be slippery clue to wax or sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet {ocations or
protectors (plugs or muffs] during extended periods of
operation.
SECURE WORK
Use clamos or a vise to hold work when practical, t's
safer than using your hand. frees both hands to operate
tool
DON'T OVERREACH
Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE
Keen tools sharp and clean for oest and safest
performance. Follow instructions for lubricating and
changing accessories
16. DISCONNECT TOOLS
before serv=cmg; when changing accessoHes such as
blades, bits. cutters etc
17. AVOID ACCIDENTAL STARTING
Make sure switch is 'n OFF poston before plugging
in.
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories. Follow the instructions that accompany
expose them to rain. Keep work area well lighted, the
Provide adequate surrounding work space, accessories. The use of improper accessories may
Cause hazards.
7. KEEP CHILDREN AWAY i9 NEVER STAND ON TOOL
AII visitors should be kept a safe distance f_om Work _ ....
area. benous Injury eou d occur if the to01 is tipped or if the
cutting tool is accidentally contacted.
8. MAKE WORKSHOP KID-PROOF Do not store materials above or near the tool such that
- with padlocks, master switches, or by removing
starter keys.
9. DON'T FORCE TOOL ....
It will do the job better and safer at the rate for which
it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment to do a job it was not
designed for.
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches) to get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair. Roll long sleeves
above the elbow
12. USE SAFETY GOGGLES (Head ProtectiOn)
Wear Safety goggles (must comply with ANSI Z87.1)
at all times. Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses. Also, use
face or dust meal( if cutting operation isdusty; and ear
it is necessary to stand on the tool to reach them.
20, CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that
is damaged should be carefully checked to ensure that it
witl operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may .affect its operation. A guard or
other part that is damaged should be properly repaired
or replaced.
21. DIRECTION OF FEED .....
Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
22, NEVER LEAVE TOOL RUNNING
UNATTENDED
Turn power off. Don't leave tool until it comes to a
complete stop.
Loading ...
Loading ...
Loading ...