Loading ...
Loading ...
Loading ...
en Cleaning functions
22
16 Cleaning functions
Use the cleaning functions to clean the appliance.
16.1 Cleaning aid EasyClean
Use the cleaning aid EasyClean for intermediate clean-
ing of the cooking compartment. The cleaning aid
EasyClean softens dirt by vaporising the soapy water.
The dirt can then be removed more easily.
Setting the cleaning aid EasyClean
WARNING‒Risk of scalding!
If there is water in the cooking compartment when it is
hot, this may create hot steam.
▶
Never pour water into the cooking compartment
when the cooking compartment is hot.
Notes
¡ The interior lighting remains off while the cleaning
aid is running.
¡ You cannot delay the end time.
¡ The length of time has been preset and cannot be
changed.
Requirements
¡ You can only start the cleaning aid once the cooking
compartment is cold (room temperature) and the ap-
pliance door is closed.
¡ Do not open the appliance door while the appliance
is in operation. Otherwise, the appliance will stop the
cleaning aid.
¡ To remove particularly stubborn dirt, leave the soapy
water to work for some time before starting the
cleaning aid.
¡ To remove particularly stubborn dirt, rub soapy water
onto the dirt on smooth surfaces before starting the
cleaning aid.
1.
Remove the accessories from the cooking compart-
ment.
2.
ATTENTION!
Distilled water in the cooking compartment leads to
corrosion.
▶
Do not use distilled water.
Mix 0.4litres water with a drop of washing-up liquid
and pour into the centre of the cooking compart-
ment floor.
3.
Use the function selector to set the cleaning
functions
.
a The
symbol and the cleaning functions appear in
the display. The first cleaning function is highlighted.
4.
Press the or button repeatedly until the symbol
is highlighted.
a
appears in the display.
5.
Turn the temperature selector.
a
appears in the display.
a The cleaning aid starts after a few seconds. The
duration counts down in the display.
a Once the cleaning aid has run through to the end,
an audible signal sounds.
Note:If
flashes in the display when the cleaning aid
is switched on, this indicates that the cooking compart-
ment has not completely cooled down. Switch off the
appliance. Wait until the cooking compartment has
cooled down and switch the cleaning aid back on.
Recleaning the cooking compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶
After using the cleaning aid, wipe the cooking com-
partment clean and allow it to dry fully.
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120°C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
1.
Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2.
Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Stubborn
residues can be removed using a stainless steel
scouring pad.
3.
Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4.
If you are unable to remove stubborn dirt, repeat the
cleaning aid after the cooking compartment has
cooled down.
5.
To switch off, turn the function selector to the zero
setting.
6.
Lower the appliance door and leave it open for ap-
prox. one hour to allow the surfaces in the cooking
compartment to dry thoroughly.
‒ To dry the cooking compartment quickly, heat up
the appliance for approx. fiveminutes at Circo-
Therm hot air
and 50 °C while the door is
open.
16.2 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
The frequency with which the appliance must be de-
scaled depends on the hardness of the water used.
The
symbol reminds you to run the descaling pro-
gramme.
There are four steps in the descaling programme. For
hygiene reasons, the descaling programme must be
run through completely so that the appliance can be
ready for operation again. Descaling takes around 90–
110minutes in total:
Display Step
First step: Descaling
Approx. 65 min
Second step: Rinse cycle
Approx. 9 min
Third step: Rinse cycle
Approx. 9 min
Fourth step: Rinse cycle
Approx. 9 min
Loading ...
Loading ...
Loading ...