Loading ...
Loading ...
Loading ...
9
ENGLISH
utilizing outboard active crossovers or requiring
full-range reproduction from one or more of the
XD800/8v2’s channel pairs.
“LP” (Low-Pass): Configures the filter to
attenuate frequencies above the selected filter
frequency at a rate of 12 dB per octave. This is
useful for connection of subwoofer(s) to one
or more of the XD800/8v2’s channel pairs in a
bi-amplified system.
“HP” (High-Pass): Configures the filter to
attenuate frequencies below the selected filter
frequency at a rate of 12 dB per octave. This is
useful for connection of component speakers to
one or more of the XD800/8v2’s channel pairs in
a bi-amplified system.
2) “Filter Freq. (Hz)” The filter frequency
markings surrounding this rotary control
are for reference purposes and are generally
accurate to within 1/3 octave or better. If you
would like to select the filter cutoff frequency
with a higher level of precision, consult the
chart in Appendix B (page 15).
Tuning Hint: If you are using the XD800/8v2
to drive a subwoofer system (“LP” mode), a
component satellite speaker system (“HP” mode)
or both, 80 Hz is a good baseline “Filter Freq.
(Hz)” setting. After properly adjusting the “Input
Sens.”, as outlined in Appendix A (page 14), you
can fine tune the “Filter Freq. (Hz)” control to
achieve the desired system frequency response.
REMOTE LEVEL CONTROL OPTIONAL
+12 VDC Ground Remote
Remote
Level
Control
CH. 5
(
L
)
CH. 6
(
R
)
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CH. 2
(
R
)
Bridged
CH. 7
(
L
)
CH. 8
(
R
)
BridgedBridgedBridged
INPUT SECTION
(
L
)
(
R
)
CH. 1&2 CH. 3&4 CH. 5&6
CH. 7&8
With the addition of the optional Remote
Level Control (HD-RLC), you can control the
volume of two, four or all eight channels of the
XD800/8v2 from the front of the vehicle. This
feature can be used for subwoofer level control,
rear channel level control, zone control, or even
as a master volume control for the system.
The HD-RLC connects to the jack labeled
“Remote Level Control” on the Connection Panel
of the amplifier using a standard telephone cable
(supplied with the HD-RLC). If desired, multiple
XD (and HD) amplifiers can be controlled from a
single HD-RLC controller using a simple,
non-duplex phone line “splitter” and multiple
phone cables.
When connected to the amplifier, the
HD-RLC operates as follows. At full counter-
clockwise rotation, the audio will mute
completely. At full clockwise rotation the level
will be the same as if the HD-RLC was not
connected at all. In other words, it operates
strictly as a level attenuator.
Remote
Level
Mode
All
|
5- 8
|
7&8
Input Mode
2 Ch.
|
4 Ch.
|
8 Ch.
CH. 7
(
L
)
CH. 8
(
R
)
CH. 7 & 8
Filter Mode
Filter Freq. (Hz)
Input
Sens.
O
|
HP
|
LP
CH. 5
(
L
)
CH. 6
(
R
)
CH. 3
(
L
)
CH. 4
(
R
)
CH. 1
(
L
)
CH. 1 & 2
CH. 3 & 4 CH. 5 & 6
CH. 2
(
R
)
Filter Mode
Filter Freq. (Hz)
Input
Sens.
O
|
HP
|
LP
Filter Mode
Filter Freq. (Hz)
Input
Sens.
O
|
HP
|
LP
Filter Mode
Filter Freq. (Hz)
Input
Sens.
O
|
HP
|
LP
CH. 1
CH. 2
CH. 3
CH. 4
CH. 5
CH. 6
(
L
)
(
R
)
CH. 7
CH. 8
INPUT SECTION
+12 VDC Ground Remote
8 Channel Amplifier
Turn-On
Mode
Rem.
|
Oset
|
Signal
Input Voltage
Low
|
High
2 Ch. Input 1 feeds CH. 1, CH. 3, CH. 5 & CH. 7
Input 2 feeds CH. 2, CH. 4, CH. 6 & CH. 8
4 Ch. Input 1 feeds CH. 1 & CH. 3
Input 2 feeds CH. 2 & CH. 4
Input 5 feeds CH. 5 & CH. 7
Input 6 feeds CH. 6 & CH. 8
8 Ch. Each input feeds its
corresponding output channel
INPUT MODES:
“Remote Level Mode” Switch: This switch
allows you to assign the operation of the
HD-RLC to one, two or all four pairs of channels.
In the “All” position, the HD-RLC knob will
affect all four channel pairs equally.
In the “5-8” (middle) position, only the level
of channels 5, 6, 7 and 8 will be affected by the
HD-RLC knob (channels 1, 2, 3 and 4 will not).
In the “7 & 8” position, only the level of
channels 7 and 8 will be affected by the HD-RLC
knob (channels 1 through 6 will not).
Loading ...
Loading ...
Loading ...