Loading ...
Loading ...
Loading ...
7
4. Press the MODE button (C) to select one of the following
operating modes:
Fan
Freeze prevention
Heating 1
Heating 2
Heating 3
4.1 Fan
In this mode, only the fan operates and the appliance does
not heat the room.
4.2 Freeze prevention
In this mode, the appliance keeps the room at a temperature
of 45°F (7°C) to avoid freezing.
4.3 Heating 1, 2 and Heating 3
In this mode, the desired temperature can be selected by
pressing the adjustment buttons + and – ( B ):
- Heating 1
The appliance operates at low power, reducing noise
levels and energy consumption to a minimum.
- Heating 2
The appliance operates at medium power.
- Heating 3
The appliance operates at high power to heat the room
rapidly.
Please note: Room temperature can be displayed in
either °F or °C. To change the unit of measurement for the
temperature, press the + button for approx. 10 seconds, then
release.
5. “ECO plus” function
The “ECO plus” function is available in Heating 1, 2 and 3 modes
only. To activate the function, press the “ECO plus” button (D).
When this function is active the appliance automatically sets
the most appropriate power level to guarantee optimum
comfort while reducing energy consumption.
While the “ECO plus” function is active, the appliance may
switch automatically to a lower heating power than the one
displayed. This may happen a number of times in an hour.
6. Swivel button
To distribute the air ow over a wider surface, press the swivel
button (F) . The appliance swivels to the right and left.
To stop the appliance in the desired position, simply press the
swivel button (F) again.
7. Turn the appliance o
To turn the appliance o, press the ON/OFF button (A).
The display may show a countdown for about 6 seconds.
Digital 24 h timer (selection from 0.5 hrs to 24
hrs)
This function can be activated from any operating mode.
Auto-start: with the appliance in ON/OFF, press the timer
button (E) . The symbol is displayed together with
the time remaining before the appliance comes on.
To adjust the timer, use the adjustment buttons + and -
(B), then wait a few seconds for the setting to be stored.
The stand-by light (H) is displayed together with the
symbol, indicating that the timer has been set. When the
programmed time is reached, the appliance comes on with
the settings used during the previous period of operation.
Auto-o: Auto-o: with the appliance on, press the timer
button (E). The symbol is displayed together with
the time remaining before the appliance goes o. To set the
timer, use the adjustment buttons + and - (B), then wait a
few seconds for the setting to be stored.
The current settings are displayed again, together with the
symbol indicating that the timer has been set. When
the programmed time is reached, the appliance goes o
automatically. To go back to operation without the timer,
press the timer button (E) twice.
The timer symbol disappears from the display.
Using the remote control
The functions on the remote control are the same as those on
the appliance control panel. For a description of the functions,
see the “Operation and use” section on the previous page.
Installing or replacing the batteries
The remote control is powered
by one CR2032 3V lithium
battery, already included
inside. To operate the remote
control, pull and remove
the plastic strip under the
battery cover. To replace the
batteries, remove the battery
cover by sliding it as shown
in the gure. When replacing
the batteries, make sure you
respect the polarity (see gure 2).
Replace the cover as shown in the gure. Old batteries are
harmful to the environment and must be removed and
disposed of in compliance with current legislation. Non-
rechargeable batteries are not to be recharged.
WARNING: DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES
MAY EXPLODE OR LEAK.
Fig. 2
Loading ...
Loading ...