Loading ...
Loading ...
Loading ...
1. Install Dispenser Assembly
Determine position of dispenser mounting
hole in sinktop or benchtop. Dispenser base
template (Diagram 5) may be cut out and
used to assist in correct positioning. Refer to
Diagram 2 for clearances allowed. Hole size
required is ø35mm.
—Stainless Steel Sinktop
A suitable 35mm hole punch (Part no: 857901)
is available as an accessory from Billi Pty Ltd.
If possible, cut hole with die mounted below
the sinktop surface so that burr is pulled
downwards. Alternatively, remove burr and
radius edge of hole with fine file. This allows
barbed dispenser mount to slide smoothly
into mounting hole.
—Timber/Laminate Benchtop
Maximum benchtop thickness is 54mm
Cut 35mm hole in appropriate position*.
When drilling through a particle board bench
top, take care to avoid a large chip breaking
away as drill breaks through underside
surface. We recommend drilling a small
pilot hole through benchtop, partially drilling
the 35mm hole from underneath and then
completing drilling the hole from above.
The large 30mm washer supplied may
be used to secure barb where underside
particle board bench top has chipped away.
* For granite or marble benchtops we
recommend you use a certified stone
mason to pre-drill the hole.
2. Activate Dispenser Swivel Feature
To activate the swivel feature of your dispenser,
you will need to remove the locking piece from
the dispenser base. Push out the piece as
shown in Diagram 6. This will allow the
tap to move 45° to the left and right.
3. Fit Dispenser Base
a. Cut a 35mm hole in sinktop or benchtop.
Remove burr if protruding upwards.
b. Push barbed mounting shaft through
mount hole.
c. Insert barb locking bush as shown
in Diagram 7. Finger tighten nut.
d. Ensure barb is centred in mount hole
before tightening. Check position of
base ring and gasket.
e. Moderately tighten locking nut using
multigrips or spanner. Take care to
avoid overtightening nut which may
break the plastic threaded shaft.
f. Place large D washer over thread as
shown in Diagram 8.
g. Cut off excess threaded shaft with a
hacksaw, using washer as a cutting guide.
IMPORTANT: Remove burrs and check internal
bore is completely smooth.
4. Fit Dispenser Head Assembly
a. Feed dispenser tubing and loom through
centre hole in the following order:
i. Dispenser power cord.
ii. Silicone tubes.
b. Gently pull hoses from under the bench
top, do not attempt to force tubing through
with a pointed object as silicone tube
is easily punctured. Check tubing is not
kinked or twisted.
c. Turn dispenser head assembly to
approximately 60° from the straight
ahead position of dispenser base.
Slide head assembly onto base assembly
whilst gently pulling tubing downwards
from underneath to prevent tubing
bunching and kinking. Mounting lugs
will pass nut and slide down the
3 grooves on the swivel bearing.
d. Once fully down, turn dispenser to
straight ahead position. Fit chrome
plated M4 retaining screw to lower rear
threaded hole and tighten using the allen
key supplied. If swivel feature activated
check dispenser now swivels smoothly
45° in each direction.
Installing the dispenser.
XL.
IMPORTANT: This Billi appliance is to be installed by a licensed tradesperson in accordance with
AS 3500.4 or AS/NZ 3500.4.2 and in compliance with applicable state regulatory requirements.
For correct operation of this appliance, it is essential to observe the manufacturer’s instructions.
Diagram 5
Silicone
tubing
Diagram 9
Diagram 6
Diagram 7
Swivel
bearing
Gasket
Barb locking bush in position
Barbed
mounting
shaft
Ensure burr
is removed
& edge has
a radius
Base casting
Locking nut
Diagram 8
Cut o
excess
thread
Remove burrs after cutting and
ensure internal bore is smooth
Barb locking
bush
dispenser base
template
Loading ...
Loading ...
Loading ...