Loading ...
Loading ...
Loading ...
NOTICE Detergent cannot be applied with the high pressure
nozzles (Cyan, Orangeor Red).
6. Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE You must attach all hoses before you start the 2.
engine.
* Startingthe enginewithoutallthe hosesconnectedandwithout 3.
thewaterturnedONwill damagethe pump.
, Damageto equipmentresultingfrom failureto followthis 4.
instructionwill voidwarranty. 5.
.
8.
Start engine following instructions How to Start Your
Pressure Washer.
Apply detergent to a dry surface, starting at lower
portion of areato be washedand work upward, using
long, even,overlapping strokes.
9. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as neededto prevent
surface from drying. DO NOTallow detergentto dry on
(prevents streaking).
NOTICE You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.
Pressure Washer Rinsing
For Rinsing:
1. Remove soap PrecisionSprayTM nozzle from nozzle
extension.
2. Selectand install desired high pressure nozzlefollowing
instructions How to Use PrecisionSpray MNozzleSystem.
3. Keepspray gun a safedistance from areayou plan to
spray.
_i, WARNING Kickbackfrom spray gun can cause you to
fall.
• Operatepressurewasherfrom a stablesurface.
= Beextremelycarefulif you mustusethe pressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
= Firmlygraspspraygunwith bothhandswhen usinghigh
pressuresprayto avoidinjurywhenspraygun kicks back.
4. Apply a high pressure spray to a small area and then
check surface for damage, if no damage is found, you
can assume it is okay to continue rinsing.
5. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Cleanin9 Detergent Siphonin9 Tube
If you used the clear detergent siphoning tube, you must
flush it with clean water before stopping the engine,
1. Placedetergent siphoning tube/filter ina bucket full of
clean water.
Remove high pressure nozzlefrom nozzle extension.
Select and install a soap nozzlefollowing instructions
How to Use PrecisionSprayTMNozzleSystem.
Flushfor 1-2 minutes.
Shut off engine following instructions How to Stop
Pressure Washerand turn off water supply.
6. ALWAYS point spray gun in a safe direction push red
button and squeezespray gun trigger to release retained
high water pressure.
NOTICE Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
_i, WARNING The high pressure stream of water that
this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.
• Keephighpressurehoseconnectedto pumpandspraygun
whilesystemis pressurized.
• ALWAYSpointspraygunin safedirection,pressredbutton
andsqueezesprayguntriggerto releasehighpressure,every
timeyoustopengine.
AutomaticCool DownSystem(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.
15
Loading ...
Loading ...
Loading ...