Loading ...
Loading ...
Loading ...
English
Controls and Functions
STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual
9
3 Hi-Z switch (channel 4)
This switch is used when connecting a device directly to the mixer without a DI
(direct box) — for example, instruments with passive pickups, such as an
acoustic-electric guitar or electric bass without a battery. This function is effective
only for the phone jack input.
4 Line (stereo) input jacks
STAGEPAS 600BT (channels 5/6, 7/8, 9/10)
STAGEPAS 400BT (channels 5/6, 7/8)
Connect line-level devices such as electronic
instruments, acoustic-electric guitars, CD
players, and portable audio players. These
jacks support phone, RCA-pin, and stereo-mini
plugs.
NOTE
For the channel 7/8 input (STAGEPAS 600BT), or for the channel 5/6 input (STAGEPAS
400BT), if both phone and RCA-pin jacks are used at the same time, the phone jack will take
priority. For the channel 9/10 input (STAGEPAS 600BT), or the channel 7/8 (STAGEPAS
400BT), if both phone and stereo mini jacks are used at the same time, the stereo mini jack
will take priority. The signal from the device connected to another jack will be muted. The
signals from the Bluetooth device specified by the Bluetooth button
9 are always mixed to
channels 9/10 (STAGEPAS 600BT) or channels 7/8 (STAGEPAS 400BT).
5 MONITOR OUT jacks
These connect to powered speakers for monitoring purposes, and output a mix of
the signals from channels 1 to 9/10 (STAGEPAS 600BT) or channels 1 to 7/8
(STAGEPAS 400BT). You can adjust the output level using the MONITOR OUT
control
A. If only the L (MONO) jack is used, the signals from the L and R
channels are mixed and output.
6 SUBWOOFER OUT jack
This connects to a powered subwoofer, and outputs a mono signal. If this jack is in
use, the low frequencies below 120Hz to the SPEAKERS L/R jacks will be cut. The
output level is linked to that of the MASTER LEVEL control
L.
7 REVERB FOOT SW jack
This connects to an unlatched-type footswitch, such as the Yamaha FC5. This can
be useful for solo performers, since you can toggle the reverb on and off as
needed with your foot.
8 SPEAKERS L/R jacks
Use the included speaker cables to connect the dedicated speakers.
9 Bluetooth button/LED
This button switches the Bluetooth function on or off. It is also used to pair
(register) a Bluetooth device (page 15). The Bluetooth LED indicates the following
status:
NOTE
The STAGEPAS enables you to pair (register) up to eight Bluetooth devices. Once the ninth
Bluetooth device has been paired successfully, the pairing information for the Bluetooth
device that was connected earliest will be deleted.
0 PHANTOM (CH1/2) switch /LED
When this switch is on, the LED lights up, indicating that phantom power is
available for channels 1 and 2. Turn this switch on to supply power to condenser
microphones or a DI (direct box).
Notice
Follow the important precautions below to prevent noise and possible damage to external
devices and the unit when you operate this switch.
• Be sure to leave this switch off if you do not need phantom power, or when you connect a
device that does not support phantom power to channels 1 or 2.
• Do not connect/disconnect a cable to/from channels 1 and 2 while this switch is on.
• Turn the LEVEL control of the channels 1 and 2 to the minimum before operating this
switch.
A MONITOR OUT control
Determines the signal level output from the MONITOR OUT jacks
5.
The MASTER LEVEL control does not affect the MONITOR OUT signal.
B Equalizer controls (HIGH, MID*, LOW) *Only for STAGEPAS 600BT
This three-band equalizer adjusts the channel’s high, mid*, and low frequency
bands. Setting the control to the “D” position produces a flat response in the
corresponding band. Turning the control clockwise boosts the selected band. If
you start getting feedback, turn the control back slightly.
C REVERB switch/LED
When this switch is on, the LED lights up, indicating that you can apply reverb.
This switch is off when you turn on the unit. (Unlike other switches, this switch
cannot be locked.)
RCA Pin Stereo Mini
LED Status
Off Bluetooth off
Lit steadily Bluetooth connected
Flashing slowly Waiting for Bluetooth connection
Flashing fast Pairing a Bluetooth device
Loading ...
Loading ...
Loading ...