Mr. Heater SRC30T User Manual

Loading ...

Operating Instructions and Owner’s ManualSunRite | Gas-Fired Infra-Red Tank Top Heater

NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!

ASSEMBLY AND HOOK-UP INFORMATION

1. HeatermodelSRC15TandSRC30Tarepackagedcom-

pletely.Propanecylinders(tanks)arenotincludedwith

heatermodel.

2. Removeheaterfromcarton.

3. UseonlyvaporwithdrawalLPgascylindersconstructed

forusewithpropaneonly(HD-5)andmarkedinaccor-

dancewiththespecificationsforLPgascylindersofthe

U.S.DepartmentofTransportation(DOTSPEC.39).

4. Thisheatermustbeusedonlywithavaporwithdrawal

LPgasbulktankequippedwithastandardPOLvalve

–donotusethisheateronbulktanksgreaterthan20

poundsLPGcapacity(50poundswatercapacity).

5a. SRC30T Dual Burner Model (see Figure 1.)

• AssemblyoftheSRC30TrequiresaPhillpsscrew-

driver.

• Thetankcollarbracketmustbeassembledbefore

theheatercanbeattachedtothepropanetank.

• Removescrewsholdingtipswitchbracketto

 manifoldcenterplateandretainforlateruse.

• Alignboltholesintankcollarbracketwithbolt

holesincenterplateonmanifoldsuchthatthe

heaterisfacingoutwardonceattachedtocylinder

collar.

• Attachedwithscrewsremovedabove,making

surethattipswitchbracketisbetweentankcollar

bracketandmanifoldcenterplate.

• Placeheaterontotankwithtankcollarbracketover

tankcollar.Mountingboltknobshouldbeposi-

tionedtotheoutsideoftankcollar.

• Firmlysecuretotankbyhand-tighteningmounting

boltknob.Donotovertighten.

• Makesureheaterregulatorisinthe“OFF”position.

• Insertregulator’sconnectorintotank’svalveand

turnleft(counterclock-wise)withhandasmuchas

possible.Donotovertighten.

5b. SRC15T Single Burner Model (See Figure 2.)

• Besureheaterisfacingawayfromtank.

• Insertregulatorconnectorintotankvalveoutlet

fittingandturnleft(counterclock-wise)untilfully

tightened.Donotovertighten.(SeeFigure2a)

• Placeheatersupportaroundventuriandslideclip

endsontopropanecylindercollar.Use1/4”-20x

Figure2a.

35mmscrewandwingnuttosecureheatersup-

portontoventuritube.(SeeFigure2b)

6. Operateonlyonastable,levelsurface.

7.  Openpropanetankvalveslowly.

8. Checkallfittingsforleaks.Applya50/50mixtureof

liquidsoapandwatertoalljoints.Bubblesforming

indicatealeakingconnection.Correctallleaksbefore

proceeding.

WARNING

 Nevertouchheaterwhileinoperationtoavoidinjury.

Moveheaterbygraspingthepropanecylindercarefully.

9. Theheatershouldbeinspectedbeforeeachuseandat

leastannuallybyaqualifiedserviceperson.

10.Thehoseassemblyshallbevisuallyinspectedpriorto

useofheater.Ifitisevidentthereisexcessiveabrasion

orwear,orthehoseiscut,itmustbereplacedpriorto

theheaterbeingputintooperation.Replacementhose

assemblyshallbeREDSTONEhoseassemblyaslistedin

thepartslist.

11. Minimuminletgaspressureis20psi.

12. Maximuminletgaspressureis120psi(equivalenttoan

ambienttemperatureof75°F(24°C)).

Figure2b.

Figure1.

Loading ...

Mr. Heater SRC30T Sunrite by 30,000 BTU Portable Convection Propane Heater

User Manual - Page 3