Loading ...
Loading ...
Loading ...
Felling
– Remove lower branches/limbs from the tree up to shoulder height.
– When removing the lower branches ensure the operator is protected from kickback by using the
tree stem for protection and keeping the guide bar out of line with the body (off set).
– Ensure there is sufficient fuel in the tank to safely complete the felling cut.
– Never leave a partially felled tree.
– When the tree begins to fall move back and away at 45º as quickly as possible. Branches on
the underside of the tree can cause the stem to move sideways or backwards dangerously.
– In the event of a tree becoming hung in another tree or obstacle seek assistance from a
professional. A hung tree poses many dangers and creates more potential risks than felling a
normal tree. Do not abandon a hung tree, walk under or attempt to climb one.
– Always perform a notch cut followed by a felling cut to create a felling hinge. Felling wedges or
levers may be necessary to prevent the chainsaw from becoming pinched in the felling cut.
Limbing
– Ensure the tree is stable before any limbering commences.
– The ideal working height for performing limbing is between waist and knee height.
– Stand on the left side of the stem, working from the root upwards, then return down the other
side.
– Use the top (pushing chain) and bottom (pulling chain) to make the cuts, constantly taking note
of the bar tip in conjunction with limbs further round the stem which may be less visible or
obscured.
– Ensure the tip of the bar does not come into contact with the ground.
– If the felled tree is on a slope always remain above the tree in case the removal of a limb were
to cause potentially dangerous movement.
– Rest the weight of the saw on the tree where possible.
– Take care of limbs and undergrowth under tension as there is a danger of spring back once the
cut has been performed.
– At regular intervals, stop the chainsaw and clear the cut debris to maintain a firm footing.
Cross cutting
– The timber must be raised off the ground with supports to perform a safe cut.
– When working on slopes, always work above the timber in case of movement.
– Always adopt a good firm footing.
– Observe the timber to assess the surfaces for tension.
– Tension and compression in supported timber can result in the timber splitting or pinching the
guide bar if incorrectly cut.
– Alleviate tension in the timber by making an initial cut (1/3) into the compressed surface before
finishing the cut (2/3) into the tension surface.
– Stand off to the side of the saw in case of kickback.
– If the chainsaw becomes trapped, switch off immediately before attempting to free the guide
bar. Use the correct tools when attempting to free a trapped saw.
– Be ready to step back quickly in case of the timber rolling.
– Ensure no debris is present in the work area.
5. HEALTH AND SAFETY INFORMATION
FIG. 32
Warning:
– Stop engine, allow to cool and engage the chain brake before carrying out maintenance or
adjustments to the machine.
– Note: Do not carry out repairs on the machine if you are not qualified to do so, with the
exemption of the items listed in this maintenance section.
10.1 CARBURETTOR ADJUSTMENT - FIG.30
Warning:
– During this operation the chain will be moving.
Ensure protective equipment is worn and observe all
necessary safety precautions.
– Note: The chain MUST NOT move while the engine
is at idle speed.
– The carburettor on your chainsaw has been set at
standard values during manufacture. Adjustments to
these values may be required occasionally.
– To adjust, start the engine and allow the machine to
idle. If the engine stalls, the idle speed is too low. If
the chain moves, the idle speed is too fast. Using a
cross slot screwdriver, turn the adjustment screw
clockwise to increase engine speed, or
anti-clockwise to decrease engine speed.
10.2 BAR MAINTENANCE - FIG.31
– Periodically clean the chain run groove and oil
passages.
– Lubricate the sprocket wheel with bearing grease.
– Reverse the guide bar on a regular basis to ensure
uniform bar wear.
– Burring of the guide bar rails is normal. Remove
these burrs as appropriate with a flat file.
– The guide bar should be replaced when the chain
run groove is worn, the bar is damaged or if
excessive burring or heating occurs.
10.3 AIR FILTER - FIGS. 32 & 33
– A clogged air filter reduces the engine efficiency,
consequently reducing cutting effectiveness while
increasing fuel consumption.
Note: The air filter should be cleaned more
frequently when the wood being cut is dry or the
work environment dusty.
– Remove the top cover by loosening securing
screw .
- 8 -
- 25 -
10. MAINTENANCE
FIG. 30
FIG. 31
Loading ...
Loading ...
Loading ...