Only replace the existing switch that independently
adjust the fan speed and the light brightness.
Do not use to control fans that have integrated fan
speed controls (i.e. fans that have a remote control or
bluetooth/WiFi enabled), unless the integrated control
is removed from the ceiling fan.
The smart switch is designed for single-pole (one
location) wiring (not compatible with 3-way/multi-way
switch wiring).
Do not use to control exhaust fans (e.g. bathroom or
kitchen exhaust fans).
This control is to be used with ceiling fans that are
rated 120W, total load 1.5 amperes maximum.
Supported Bulb Types: Dimmable LED/CFL - 150W
Max; Incandescent - 300W Max. Not compatible with
non-dimmable light bulbs.
Neutral wire is required to install the smart switch. If
your house was built or remodeled before mid-80's,
you may not have a neutral. Please try another
location or call an electrician for help.
Install your Treatlife switch where there is a strong
Wi-Fi signal.
Keep your mobile device close to the Treatlife smart
switch until setup is complete.
Note: Use the ceiling fan’s pull chain or wall control
to set its speed to the highest setting before remove
the previous ceiling fan control.
Press each light switch at the location you’re doing the
installation to confirm power is off.
If a light turns on, return the panel to turn off the correct
circuit. We recommend you to remove the faceplate from
the old switch and use electrical tester to test all wires
connected to the switch to ensure there is no voltage in
the circuit.
You may need to turn off more than one circuit breaker.
2
Verify That Power Is Off
ATTENTION
Locate your circuit breaker panel and turn off the power to
each switch you are replacing
Risk of shock.
Make sure the power to every switch you are replacing has
been turned off before installation.
Please call a professional electrician if you are not familiar
with electrical work.
Caution: Caution:
1
Turn Power Off
TROUBLESHOOTING
Can’t connect to the APP.
ADD DEVICES
PRODUCT APPEARANCE
1. Download the TreatLife APP
2. Registration or Log In
Tap “Register” to create an account. Enter your email
address to get a verification code and create a password.
Or, choose “Log in” if you already have a TreatLife
account.
3. Configure the APP to the Switch
Note:
This switch only supports 2.4GHz networks. If you connect-
ed to a 5GHz network before, please switch to the 2.4GHz
Network.
Preparation: Ensure the switch is connected to power;
Ensure your phone is connected to your WiFi router and
is able to connect to the internet.
Please scan the QR code or search “TreatLife”
on the Apple APP Store / Google Play to download the APP.
Go to TreatLife> >More for instructions to link Alexa/-
Google Assistant.
Please make sure the red indicator light is blinking when
you are attempting to connect to the APP. Default Mode
Paring: Red Indicator Blinking rapidly. AP mode Paring:
Red Indicator Blinking slowly.
Please finish the pairing within 3 minutes when the red
indicator starts blinking. (Refer to “Me-FAQ&Feedback"
in the APP)
The smart switch shows the wrong status in the APP.
The network may be delayed or the network signal is
weak.Try to move the router closer to the switch or
power off the router and then power it on. If it still
doesn’t work, try to replace the light bulb with a different
model or brand bulb.
Can’t connect to Alexa.
Check whether the Alexa APP is correctly configured
with the account of TreatLife APP. Refer to the manual
instruction or “Me--FAQ&Feedback--All-Third-party
control issues" in APP to reconnect to Alexa.
If your router is 2.4GHz & 5GHz dual-band, the 2.4GHz
band may not be turned on. Please enter the router
settings to turn on the 2.4GHz band. You can check the
router's manual or contact the router's official support
for help.
Make sure you entered the correct WiFi password.
Note: Please log in with your TreatLife account.
Tap the icon “+” on the top right corner to Select Device
Type; tap “Smart Switch” and choose “Celling Fan Dimmer”.
Press the “ ” button, turn the light on or off.
Double-press the “ ” button, press the “+”/ “-” button
to brighten/dim the light in stages.
Long press the “+”/ “-” button, brighten/dim the light
continuously.
Unscrew the old switch and pull it out of the wall. Do not
remove any wires.
A neutral is required to install the smart light switch.
Make sure there are NEUTRAL wires (most likely a bundle
of one or more white wires ) in the wall. Unless you are
replacing an existing smart switch, it’s probably not
connected to your old switch.
3
Pull Out the Existing Switch
Remove the sticker securing the wires on the new switch.
Connect NEUTRAL/GROUND Wires
Use wire nuts to connect the neutral and ground wires on
the Treatlife Smart Switch to the labeled wires coming from
the wall in order.
Connect LINE Wires
Use wire nuts to connect the line wire on the Treatlife Smart
Switch to the labeled wires coming from the wall in order.
Connect Light/Fan Load Wires
Use wire nuts to connect the Light and Fan Load wires on
the Treatlife Smart Switch to the labeled wires coming from
the wall in order.
10
Wire the Smart Switch
6
Identify Line Wire
Label the LINE wire (usually BLACK, attached with a
black screw, and may be labeled “common".) in the
wall with the “Line" sticker.
7
Identify Light / Fan Load Wire
Label the Load (Light) wire in the wall with the“Light
Load" sticker.
Label the Load (Fan) wire in the wall with the “Fan
Load" sticker.
8
Take Pictures of the Wiring
Note: Make sure all of the text on the labels in the
pictures is clearly displayed.
Note: Do not over tighten the screws, as it could restrict
the operation of the switch.
Note: If you can't use the voice control correctly, try to
remove the device from TreatLife APP then reconfigure
it again. If it still doesn't work, confirm the individual
device name for the fan and light in smart life APP is
the same as the Alexa/Google Home APP.
11
Install Smart Switch Into the Wall
If you encounter any problems, please contact us via
email: [email protected]
(Please be sure to attach the wiring pictures of the
old switch in step 8 )
5
Test NEUTRAL and GROUND Wires
Make sure there is no power on the neutral wires from
neighboring circuit. If necessary, shut off additional circuits
until no voltage is found.
GROUND wires are usually BARE COPPER or GREEN.
Take one or two pictures of the old switch and where each
wire is connected, in case you need guidance to repeat
the installation.
9
Remove Existing Switch
Loosen the screw terminals and remove the old switch.
Hold the wire nuts and gently pull each wire to make sure
the wire nuts are secure. Carefully push the wires deep into
the switch box. Attach the smart switch to the switch box
with the screws provided. Finally, snap on the faceplate.
12
Turn on Power
Turn power back on at the circuit breaker.
Press the on/off button to confirm whether the switch is
powered on/off normally. If the light fixture/ceiling fan can
not be turned off/on, or sometimes the fan switch can not
be turned on or off, the wiring maybe incorrect or the nuts
are loose. Please refer to the instructions in the manual or
call an electrician for help.
Note: If there is no neutral, please try another location or
call an electrician for help.
Note: If there is no neutral, please try another location or
call an electrician for help.
Screwdriver Pliers Electrical Tester
The Tools You'll Need
4
Identify Your Existing Switch
Link TreatLife to Alexa/Google Assistant
Key Steps to Link the Alexa Skill
RSS (Category I Equipment)：
This device complies with Innovation, Science, and Economic
Development Canada's licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’ Innovation,
Sciences et Ddveloppement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions
suivantes :
(1) I’appareil nedoit pas produire de brouillage, et
(2) I’utilisateur de I’appareil doit accepter tout brouillage
radioélectri- que subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines, users
can obtain Canadian information on RF exposure and
compliance.The minimum distance from body to use the
device is 20cm.
Le présent appareil est conforme
Après examen de ce matériel aux conformit6 ou aux limites
d’inten- sité de champ RF,
les utilisateurs peuvent sur I’exposition aux radiofréquences
et la conformité and compliance d'acquérir
les informations correspondantes. La distance minimale du
corps à utiliser le dispositif est de 20cm.
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver. -Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures：
Press and hold the mechanical light control on/off button
for 5 seconds until the red indicator light blinks rapidly.
Tap “Confirm indicator rapidly blink”; Enter your WiFi
Password; Wait for the switch to complete.
Repeat steps to add any additional smart switches.
Sign in With Amazon, tap on “Skills & Games” in the
Alexa menu；
Search for the “Smart Life”, and tap “Enable” to enable
the Skill.
Enter the “TreatLife” APP Account and Password, then
tap “Link Now” to enable the Skill.
DS03
Warning:
Never use a neutral wire in place of a light or fan load wire.
Circuit breaker panel
Circuit breaker panel
Brightness
Brightness
Brightness / Fan
Speed Indicator
Rapidly
Light Fixture Control
Press and hold the “ ” button for 5s until the Wi-Fi
indicator light blinks red quickly (twice/1s) to reset the
device and initiate default configuration.
When the indicator blinks quickly (twice/1s), press and
hold the “ ” button for 5s until the Wi-Fi indicator light
blinks red slowly (once every 3s) to initiate AP configura-
tion.
Pairing Settings
Press the “ ” button, turn the fan on or off.
Double-press the “ ” button, press the “+”/ “-” button
to increase/decrease the fan speed in stages.
Ceiling Fan Control
Long press the “+”/“-” button to increase/decrease the
fan speed quickly.
3.1Default Configuration Mode
If you can not configure the switch successfully with the
default mode, please try to connect with AP Mode.
Tap “AP Mode” on the top right corner.
Press and hold the mechanical light control on/off button
for 5 seconds, until the red indicator light blinks rapidly.
Then press and hold for 5 seconds again until the
indicator light blinks slowly.
Tap “Confirm indicator slowly blink”.
Enter your Wi-Fi Password.
Open WLAN settings; the Wi-Fi settings on your phone
and connect to the “TreatLife-xxx” network.
Go back to the APP and continue to add the device then
wait for the connection to complete.
3.2 AP Mode
The Timing function doesn’t work properly.
Remove the switch from APP, and repair the switch to
APP again; You can also check Me-> FAQ & Feedback
information in the APP. If it still doesn't work, please
provide the Virtual ID in the APP to us.
Can’t dim lights manually.
Check if they are dimmable light bulbs, if not, change to
another non-smart dimmable light bulb.
There is a noise with the fan switch or light bulb.
Change to another different model of non-smart dimmable
light bulb.
Lights are too bright even on minimum level.
Go to TreatLife > dimmer setting to decrease the dimming
range.
Lights are too dark or not light up even on minimum level.
Go to TreatLife > dimmer setting to increase the dimming
range.
Lights Flickering
If they are dimmable light bulbs, go to TreatLife > dimmer
setting to switch the mode or adjust the dimming range;
If they are not dimmable light bulbs, change to non-smart
dimmable light bulbs.
Wires not secured firmly with wire connectors.
After turning off the light, the light bulb flickers or is not
completely turned off.
Replace the light bulb with a different make/model.
After using the switch for a period of time, manual
operation doesn’t work properly.
Turn off the power at your circuit breaker panel for a few
minutes and then power it on again.
One of several Treatlife smart switches doesn’t work properly.
Replace this switch with one of the known good ones to
ensure everything is wired properly. If it still doesn't work,
please contact our support.
Fan speed is too slow.
Ensure that the fan is set to highest possible setting
before install Treatlife smart fan switch.
Neutral
Ground
Line
lartueN
Ground
lartueN
dnuorG
Line
Lighting Load
Fan Load
lartueN
dnuor
G
Line
Lighting Load
daoL naF
lartueN
dnuorG
Line
Fan Load
daoL gnithgil
lartueN
dnuorG
Line
Lighting Load
Fan Load
bedroom Light
bedroom fan
TreatLife-XXXX
lartueN
dnuorG
Fan Load
Line
Lighting Load
材质：105g 铜版纸 颜色：双面彩印 尺寸：513*234mm（5折6页）
Label the NEUTRAL and GROUND wire in the wall with
the stickers in the package.