Loading ...
Loading ...
Loading ...
10 CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6056
• Press the “▲” or “▼”button to move the cursor
to the corresponding date, press the “+” button to
add the corresponding date, or press “-” button to
delete the date. Continue until you have completed
the selection of all dates.
3. Set the Timer ON time
• Press the “TIMER SET” button; the hour starts
blinking.
• Press the “+” or “-” button to adjust the hour.
• Press the “TIMER SET” button; the minute starts
blinking.
• Press the “+” or “-” button to adjust the minute.
4. Set the Timer OFF time
• Press the “TIMER SET” button; the display is OFF,
and the hour starts blinking.
• Press the “+” or “-” button to adjust the hour.
• Press the “TIMER SET” button; the minute starts
blinking.
• Press the “+” or “-” button to adjust the minute.
5. Set the temperature
• Press the “TIMER SET” button, and the
temperature set starts blinking. At this moment,
the temperature displayed is normally the set
temperature, which can then be adjusted by
pressing “+” or “-” button.
6. Press the “TIMER SET” button and then press the
“OK” button to complete the setting programme.
Steps to view the timer setting:
• Press the “TIMER SET” button.
• Press the “+” or “-” button to check the Timer ON
times one by one.
• To check the Timer OFF times, press the “▲”
button.
• Press the “+” or “-” button to continue viewing.
• For deleting the current item of timer setting, press
the “C” button to delete.
Safety Cut-Out:
• This appliance is tted with a safety cut-out
which will operate if the re overheats (e.g. due to
blocked air vents). For safety reasons, the re will
NOT automatically reset.
• To reset the appliance, disconnect the appliance
from the mains supply for at least 15 minutes.
• Reconnect the supply to the mains and switch on
the appliance.
CAUTION! Do not touch the re as it will be hot. Set the
heater switches to OFF and leave the re to cool down
fully. Once completely cool, reconnect the heater and
switch it on. Do not open this product. There are no
user-serviceable parts inside.
CHECK THAT YOU HAVE NOTED ALL THE
FOLLOWING INSTRUCTIONS:
Do:
• Always install the re in accordance with this
guide. If in doubt obtain expert advice.
• Always make sure the electrical socket is
accessible and located adjacent to, but not above
or behind the re.
• Always disconnect the re from the electrical
supply before carrying out cleaning or
maintenance.
• Always make sure the re is rmly secured.
• Always assemble the re in accordance with this
guide. If in doubt, obtain expert advice.
• Always ensure the product is assembled in an area
that is free from dust, grease or liquids.
• Always ensure that the correct tools are used to
assemble/install this product.
• Always make sure the re is rmly secured in place
when complete.
Don’t:
• Never leave children unsupervised in a room where
the re is ON and unguarded.
• Never obstruct or cover the fan outlet or force
items into the re openings.
• Never install or use the re anywhere where water
is in use, i.e. bathrooms, kitchens, shower rooms,
swimming pools etc.
• Never use aerosols or steam cleaners on or
around the re.
• Never route the mains supply cable under carpet
etc.
• Never install the re close to curtains or
combustible materials.
• Never use the re to dry clothes etc.
• Never sit or stand on the re.
• Never cut the o the plug and hard wire into a
xed fused spur.
NOTE: Any new wiring required, must be in accordance
with local and national codes and other applicable
regulations in order to reduce the risk of re, electric
shock, or other injuries.
NOTE: When the re is turned on for the rst time
or when it has not been used for some time, it may
release a slight, harmless odour. This odour is a normal
occurrence caused by the initial heating of the internal
heating elements or dust, and will disappear with use.
Loading ...
Loading ...
Loading ...