The successive wash-dry programme automatically shifts from the wash cycle to the dry cycle without further intervention.
Drying is achieved using the condensation principle. The condensate that is produced during drying runs via the Drain hose into the Drain tank.
Caution: the water supply hose and water Drain hose must be correctly connected during washing and drying The tap must be open.
A safety device prevents the door from being opened during operation.
Before opening
Make sure that there is no water in the drum and that the drum is not moving.
Emergency release
In the event of a power cut, the door can be released mechanically
Control panel
Before washing for the first time
The washer-dryer was tested before leaving the factory.
To remove any water that may be left over from the test, do not load any laundry the first time that you run a wash programme.
Make sure that the transport safety bolts on the rear of the washerdryer have been removed.
Do not load any laundry.
Close the door.
Turn on the tap.
Pull out the detergent drawer.
Add ½ a measuring cup of detergent to compartment II –> page 11.
Do not use detergents for wool or delicates (these cause foam to be created).
Close the detergent drawer.
Turn the programme selector to the 60°C programme.
Press the Start/Pause button.
At the end of the programme, turn the programme selector to Off.
Open the door.
Leave the door open to allow the inside of the washer-dryer to dry
Preparing and sorting the laundry
Sorting laundry for washing
Wash white laundry separately from coloureds.
Unhemmed or torn items should not be washed in the washer-dryer, as they may fray.
The laundry may be damaged if you do not observe the fabric care symbols.
Only wash laundry with the following care labels:
Sorting laundry for drying
Only dry laundry that is labelled "suitable for tumble-drying" or which has the following care symbols:
Do not wash the following fabrics in the washer-dryer:
Do not machine dry laundry with the care symbol.
Airtight fabrics (e.g. rubber-coated fabrics).
Delicate materials (silk, curtains made from synthetic fabrics) - they may crease.
Dripping-wet laundry - high energy consumption
Wool or fabrics containing wool.
Preparing laundry for washing
Loose foreign bodies (e.g. coins, paper-clips, needles, nails) may damage the laundry and components of the washer-dryer (e.g. the drum).
Drain the pockets of all items.
Brush any sand out of pockets and collars.
Pretreat any stains.
Close zips, do up cover buttons.
Remove curtain fittings or place curtains in a laundry bag.
Wash the following in a laundry bag/pillowcase:
Delicates, e.g. tights, curtains,
Small items, e.g. socks or handkerchiefs,
Underwired bras (the underwiring may come loose during the washing process and cause damage).
Turn trousers, knitwear and knitted fabrics, e.g. jerseys, T-shirts or sweatshirts inside out.
Preparing laundry for drying
Only dry fabrics that have already been washed, rinsed and spun.
Also spin easy-care fabrics before drying.
Sort the items for washing according to material and desired level of dryness to ensure even drying.
Detergents and Care Product
Detergent drawer
The detergent drawer is divided into three compartments
Compartment I : detergent for pre-wash.
Compartment II : detergent for main wash,
Compartment : Liquid additives, such as starch or fabric softener.
Additives are automatically dispensed during the final rinse cycle.
Do not exceed the maximum capacity, otherwise compartment i may be emptied too early.
Dilute viscous additives with water to prevent blockages.
Liquid detergent insert: this must be inserted before liquid detergents are used.
To do this:
Pull out the detergent drawer as far as the stop.
Press on the zone labelled PUSH and take out the detergent drawer.
Pull the insert in compartment II forwards as far as the stop and push it down.
Insert the detergent drawer.
Descaler
Descaler can be added to compartments I and II according to the manufacturer's instructions. Add detergent first, followed by the descaler.
Detergents and care products
Normally soiled laundry
Set the programme.
Do not select (Pre-wash).
Add all the detergent, according to the manufacturer's instructions, to compartment II of the detergent drawer.
Heavily soiled laundry
Set the programme.
Select (Pre-wash) .
Add 1/4 of the recommended amount of detergent to compartment I of the detergent drawer and 3/4 of the detergent to compartment II.
Measuring liquid detergent
Only use liquid detergent for the main wash cycle with no prewash.
To do this:
Add the recommended amount of detergent to a liquid detergent measuring aid and place it in the drum.
or
After folding down the liquid detergent insert, pour the detergent into compartment II of the detergent drawer.
The scale on the liquid detergent insert helps to measure the correct dosage of liquid detergent.
If compartment II is used for washing powder, the liquid detergent insert must be folded up
Programmes
Programme selector
The programme selector is used to set the washing and drying programmes.
The time remaining until the end of the programme and the Beladungsmenge (Load) are shown on the display panel.
Washing programmes
* depends on the model
Cottons
Suitable for hard-wearing fabrics, heat-resistant fabrics made from cotton or linen.
Coloureds up to 60 °C.
Whites 60 °C to 90 °C.
Cottons Eco
Washing programme for the best possible washing result with minimum energy and water consumption.
Easy-Care
Washing programme for less hard-wearing fabrics made from cotton, linen, synthetic fibres or blended fabrics. It is advisable to sort the laundry by colour.
Delicates/Silk
Gentle programme for delicate, washable fabrics, e.g. silk, satin, synthetics or blended fabrics (e.g. curtains). Gentle spinning between the rinse cycles and reduced final spin speed.
Wool
Wool becomes matted when subjected to heat, moisture and movement. The woollens programme takes these qualities into account and finds a compromise between standing still and movement.
Suitable for hand- or machine-washable fabrics made from wool or a wool blend.
Rapid 15’
Short programme for easy-care, lightly soiled fabrics made from cotton, linen, synthetics or blends. Suitable for freshening up items or for washing new items before wearing for the first time. The programme takes 15 minutes.
Mix
For mixed items of laundry made of various hard-wearing and easy-care fabrics.
Sports
For washing functional clothing and sports wear made from microfibre and synthetics. Reduced creasing and additional rinse cycle.
Washing programmes
* depends on the model
Sensitive
For washing fabrics with increased hygiene requirements or those that will be used by allergy sufferers. The temperature remains constant during the washing process. More intensive rinsing with increased water level. For hard-wearing and easy-care fabrics made from cotton or linen.
Night Wash
Particularly quiet wash programme with a reduced final spin.
Sleep mode. Once the programme has finished, the display goes out, but can be reactivated by pressing any button.
Drying programmes
Intensive Dry
Intensive drying for a (robust fabrics), at 90°C.
Gentle Dry
Gentle drying for (easy-care fabrics), 60°C.
Special programmes
Fluff Clean
The drum must be empty.
This programme is designed to clean the drying cycle of any fluff deposits. The washer-dryer uses the flashing symbol (Fluff removal cycle) in the display panel to show that this programme must be run. The electronic cycle counter is then automatically reset. The (Fluff Clean) symbol goes out after the programme starts.
To run the Fluff Clean, proceed as follows:
Make sure that the drum is completely empty and close the door.
Turn the programme selector to Fluff Clean.
Press the Start/Pause button.
The Fluff Clean programme can also be run at any time without prompting by the appliance.
Rinse + Spin:
An additional rinse cycle with a final spin. If the laundry is to be removed dripping wet, set the Spin speed to $ (Rinse hold) before Programme start.
Drain + Spin:
Drain the rinsing water following a programme with (Rinse hold) .
Turn the programme selector to Drain + Spin.
Set the spin speed to (Rinse hold).
Press the Start/Pause button.
or
Drain and spin at the desired spin speed:
Turn the programme selector to Drain + Spin.
Press the Spin button repeatedly until the desired spin speed is set.
Press the Start/Pause button.
Washing and drying options
Temp. button
The temperature can be adjusted individually for each programme. To adjust it, press the Temp. button repeatedly until the required temperature is displayed.
Spin speed button
The spin speed can be individually adjusted for each programme. To set the spin speed, press the Spin button repeatedly until the required spin speed is displayed.
Rinse hold
Rinse hold) deactivates the spin function. The laundry remains in the rinsing water.
Unbalanced load detection system
The automatic unbalanced load detection system ensures that the laundry is evenly distributed using several initial spins. If the laundry is extremely unevenly distributed, the speed of the final spin is reduced or the spin cycle is not performed for safety reasons.
Option button
The set programmes can be individually adjusted.
To choose the required option:
Press the Option button repeatedly until the required option is selected (indicator lamp flashes).
Press the Set button to switch the option on/off (indicator lamp lights up/does not light up).
Set button
If you press and hold the Option ~ button, all the options scroll through.
Options (symbols on the display panel)
Delay button
You can postpone Programme start before it begins. Using the Remaining time, you can determine when the selected programme is to end. The remaining time can be set in one-hour increments, up to a maximum of 24 hours. Press the Delay button repeatedly until the required number of hours is displayed. Then press the Start/Pause button, the programme will start after a delay according to the set (Remaining time). The required time to the end of the programme is shown on the display panel.
Dry button
The drying programmes can be individually adapted by selecting the drying options.
Press the Dry button repeatedly until the required drying option is shown on the display panel.
To deactivate, press the Dry button repeatedly until is shown on the display. Drying options (symbols on the display panel)
Drying options (symbols on the display panel)
Start/Pause button
Press the Start/Pause button to start the selected programme. The (Remaining time) is shown on the display panel. The (Programme start) symbol is lit
Programme progress
The programme progress is shown on the display panel:
Changing the programme
To change the programme:
Select a new programme.
Press the Start/Pause button.
Pausing the programme
Press and hold the Start/Pause button while the programme is in progress until appears on the display panel. and the (Remaining time) appear alternately on the display while the programme is paused. Press the Start/Pause button to continue with the programme.
Cancelling the programme
Press and hold button Start/Pause until is displayed.
For washing programmes at high temperatures:
Cooling down laundry: choose Rinse + Spin.
Press the Start/Pause button.
For programmes at low temperatures:
choose Drain + Spin.
Select the Start/Pause button.
Cleaning and care
Housing and control panel
Wipe with a soft, damp cloth.
Remove detergent and cleaning agent residue immediately.Do not clean with a jet of water.
Drum
Remove any foreign bodies from the drum and rubber seals.
Descaling the drum:
Only use a proprietary brand of descaler with corrosion inhibitor for washing machines for descaling the washer-dryer.
Observe the manufacturer's instructions regarding use and dosage.
After descaling and removing rust from the drum, run the Rinse + Spin programme several times to remove any remaining acid.
If any remaining metal objects (e.g. coins, paper clips, needles, nails) have caused rust spots:
Use chlorine-free cleaning agents; observe the manufacturer's instructions. Never use steel wool.
Detergent drawer
If there are detergent or care product residues:
Pull out the detergent drawer as far as the stop.
Press on the blue zone labelled PUSH and take out the detergent drawer.
Clean the detergent drawer guide.
Remove the blue fabric softener compartment insert.
Clean the detergent drawer and fabric softener compartment insert under running water.
Insert the fabric softener compartment insert.
Insert the detergent drawer.
Drain pump
Set the programme selector to Off.
Use a screwdriver to release the lock pins.
Tip the kick panel and pull upwards to remove
Draining the water
Take the Drain hose out of the retainer.
Remove the plug from the Drain hose and release the washing water.
The container for the Drained water may have to be emptied several times.
When no more water runs out, replace the plug.
Place the Drain hose into the retainer.
Cleaning the Drain pump
Unscrew the pump cover.
Clean the pump housing and remove any foreign objects.
Make sure that the impeller can turn freely.
Replace the pump cover and screw firmly in place.
Place the kick panel in the 4 clip-in slots and secure to the housing using the lock pins.
Filter in the water supply hose
If no water runs into the washer-dryer, or only an insufficient amount, you must first reduce the water pressure in the supply hose:
Turn off the tap.Drain + Spin.
Press the Start/Pause button.
Allow the programme to run for approximately 40 seconds.
Set the programme selector to Off.
Unplug the mains plug from the socket.
Unscrew the water supply hose from the tap.
Clean the filter with a small brush.
Reconnect the hose.
Turn on the tap.
Check whether water comes out of the end of the hose.
If water is escaping, check that the filter is correctly seated.
Descaling the washer-dryer
This should not be necessary if the correct detergent dosage has been used. If it is necessary, however, proceed according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or from our after-sales service
What to do if...
Fault code
The door is not properly closed. Close the door.
The water control system has been activated. Disconnect the appliance from the mains, turn off the tap and advise the after-sales service.
Water is not entering the appliance. See the fault Water is not flowing in.
The water is not Drained. See the fault Water is not Drained.
Not a fault The unbalanced load detection system has detected an unbalanced load caused by laundry items. The fluff removal cycle cannot start. Remove the laundry.
Maximum or minimum drying load not taken into account. HI/End or LO/End flash alternately in the display. See the fault Drying result not satisfactory.
Other fault codes are only for use by the after-sales service. Make a note of the fault code to inform the after sales service
Fault
Possible cause
Remedial action
Programme does not start.
The Start/Pause button has not been pressed.
Press the Start/Pause button.
A delayed start time has been selected.
Washer dryer starts on completion of the delay period. Change the “finished in time” if necessary
Power cut. The delayed start time that was selected has been cleared.
Reselect the delayed start time or start the programme immediately. Press the Start/Pause button.
The door is not properly closed.
Close the door.
Plug not inserted properly into socket.
Insert plug correctly.
The maximum spin speed cannot be set.
The maximum spin speed depends on the programme selected.
Change programme as required.
The water is not Drained.
Damp or lumpy detergent.
Clean and dry the detergent drawer
Use the measuring aid for liquid detergent.
Water is not flowing in.
The mains plug is not correctly plugged in.
Plug in the mains plug correctly.
The door is not properly closed.
Close the door.
The tap is not turned on.
Turn on the tap.
The filter in the water supply hose is blocked.
Clean the filter in the water supply hose
The water supply hose is pinched or kinked.
Check the water inlet hose.
Intense vibrations during spinning.
The washer-dryer is not correctly levelled.
Level the washer-dryer
The transport safety bolts have not been removed.
Remove the transport safety bolts
Washer-dryer fills with water and continuously Drains it away.
Drain hose fitted too low
Fit the Drain hose correctly
No water can be seen in the drum.
Not a fault.
During certain programmes the water level is below the visible range.
Water leaks from the bottom of the appliance.
Supply hose screw connection is leaking.
Tighten the screw connection.
Drain hose is leaking.
Have the Drain hose replaced by the after-sales service.
Foam escapes fro
Too much detergent has been used.
Only use detergent which is correct for textiles, and suitable for use in automatic washing machines. Make sure that you use the correct dosage
Several attempts to start spinning.
Not a fault. The unbalanced load detection system attempts to redistribute an unbalanced load by starting to spin several times.
Always wash large and small items together.
Washing is not spun properly.
Large items of laundry are not evenly distributed in the drum. The spin speed is automatically reduced for safety reasons.
Always wash large and small items together
Washing results not satisfactory
Uncleaned areas worse than expected.
Select a suitable programme, e.g. a programme with Pre-wash. Pretreat stains if necessary.
Too little or incorrect detergent used.
Use the correct dosage of a suitable detergent, in accordance with the manufacturer's instructions.
Maximum load exceeded.
Select the load appropriate for the programme.
Detergent residues on the washing.
Some phosphate-free detergents contain water-insoluble residues which appear on washing as light specks.
Rinse the laundry again or change to using liquid detergent. Brush the laundry after it has dried
Grey residues on the washing.
Soiling caused by ointments, grease or oil.
Wash the laundry using the maximum detergent dosage and the maximum permissible temperature – see the care label.
Programme terminated unexpectedly.
The Start/Pause button was selected accidentally.
Press the button again to restart the programme.
Spinning during drying
No fault
"Thermo spin", which is for energy-efficient drying, starts after a drying time of approx. 10 minutes.
Drying result not satisfactory
The laundry clings to the sides of the drum after being spun.
Loosen up the laundry by hand; start the drying programme
Closed tap
Turn on the tap.
Selected drying time too short.
Select the drying time according to the Load.
Maximum or minimum load not taken into account
Once the programme has ended: adjust the load quantity, select a suitable drying programme and restart.
The fabric softener is not completely flushed in or too much water remains in the compartment .
The fabric softener compartment insert is not correctly attached or is blocked.
If necessary, clean the fabric softener compartment insert and fit it correctly in compartment
The laundry is not dried.
The tap is turned off
Turn on the tap.
The load is too large.
Reduce the load size.
The drying time is too short.
Select a suitable drying time.
No display on the display panel.
Power cut.
The programme continues when power is restored. If you wish to remove the laundry during a power cut, you must first Drain out the water
Check whether:
the plug is plugged into the socket correctly.
the circuit breaker (fuse) has tripped; if it has, call the after-sales service
The door cannot be opened.
(Rinse hold) has been selected.
Select the programme Drain + Spin and press the Start/Pause button.
The programme is running or the door is locked for safety reasons.
Wait until appears on the display panel.
Power cut.
Unlock the door mechanically
Emergency release
To release the door mechanically in the event of a power cut:
turn the programme selector to Off and unplug the mains plug from the socket.
open the base panel and Drain out the water
pull the emergency release downwards and open the door at the same time.
Before opening the door, make sure that there is no water or hot detergent solution in the washer dryer.
WARNING Under no circumstances open the door with the emergency release while the drum is still turning.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
Turn the programme selector to Off and unplug the mains plug from the socket.
care symbol.
: Liquid additives, such as starch or fabric softener.
(Pre-wash).
Wool
(robust fabrics), at 90°C.
(easy-care fabrics), 60°C.
(Fluff removal cycle) in the display panel to show that this programme must be run. The electronic cycle counter is then automatically reset. The
(Rinse hold) .
Rinse hold) deactivates the spin function. The laundry remains in the rinsing water.
(Remaining time). The required time to the end of the programme is shown on the display panel.
is shown on the display. Drying options (symbols on the display panel)
(Programme start) symbol is lit
appears on the display panel.
is displayed.
.
(Rinse hold) has been selected.
appears on the display panel.
