Loading ...
Loading ...
Loading ...
Problem Cause Acon
Dishwasher not
lling with water
Restricon in the water supply system.1.
Previous wash cycle was not completed.2.
Delay-start is acve.3.
Ensure that the water supply valve (typically located under kitch-1.
en sink) is open and check that the water supply line has no kinks
and clogs.
Refer to the “Canceling or changing the cycle” secon of this 2.
manual.
Cancel the delay-start or wait unl delay-start me completes 3.
(mes out). Refer to the “Delay Start” secon of this manual.
Water Leaks Suds1.
Door seal could be pulled away from track.2.
Condensaon vent is blocked.3.
Improper installaon.4.
Wrong type of detergent results in suds and leaks. Use only 1.
dishwasher detergents. If suds sll persist, then add one ta-
blespoon of vegetable oil at the boom of the dishwasher
and run the desired cycle.
Ensure that door seal is in the track.2.
Ensure that condensaon vent is not blocked. Refer to “Load-3.
ing Extra Tall Items” in the Preparing and Loading the Dish-
washer secon of this manual.
Have proper installaon veried by qualied personnel (wa-4.
ter supply, drain system, leveling, plumbing).
Tub stains Stains on the dishwasher interior are due to hard-1.
ness of water.
Silverware in contact with tub.2.
Concentrated Lemon juice can reduce the build up of hard 1.
water stains. Run a normal cycle unl it ushes and interrupt
the cycle and then place an 8 oz. cup of the concentrated
lemon soluon on the top rack and nish the cycle. This can
be done periodically to avoid build up.
Ensure that the silverware does not make contact with the 2.
tub while running a cycle.
Streaks on glass-
ware or residue
on the dishes
Incorrect rinse agent seng. Depending on the hardness of water, adjust the rinse agent dis-
penser. Refer to “Adding Detergent and Rinse Agent” secon in this
manual for adjustment.
Fascia panel
discolored or
marked
Abrasive cleaner used. Use mild detergents with so damp cloth.
Noise during
wash cycle
The dishes may not be arranged properly. Water circulaon sound is normal, but if you suspect items are
banging into each other or into the spray arms, refer to the “Pre-
paring and Loading” secon of this manual for opmal arrange-
ment.
Detergent dis-
penser cover will
not shut
Improper operaon of detergent cover.1.
Previous cycle has not been nished, reset, or cycle 2.
was interrupted.
Refer to “Adding Detergent and Rinse Aid” secon of this man-1.
ual for instrucons on opening and closing the dispenser.
Refer to the “Canceling or changing the cycle” secon of this 2.
manual.
Unable to select
desired cycle
Previous cycle has not nished or another cycle has
already started.
Refer to the “Canceling or changing the cycle” secon of this
manual.
Error Codes
If fault code (E01 to E30) is indicated on the digital display 3 , rst disconnect the appliance from the power supply. You can
recfy certain faults yourself (see following fault descripon), for all other faults please contact customer service and state the
indicated fault E:XX.
Water is le in
the appliance
at the end of the
programme
(E24) Waste water hose is blocked or kinked.1.
(E25) Waste water pump blocked, cover on the 2.
waste water pump is not locked in posion
Filters blocked.3.
The programme has not yet ended.4.
See Care and Maintenance.1.
Wait unl programme ends (digital display indicates 0:00) or 2.
implement the ”Reset”funcon.
“Check water
supply” display
lights up
Tap turned o.1.
Water supply interrupted.2.
Supply hose kinked.3.
Filter in the water supply blocked4.
Switch o the appliance and pull out the main plug.1.
Turn o the tap.2.
Clean lter in the supply hose.3.
Reconnect power supply.4.
Turn on the tap.5.
Switch on the appliance.6.
20
Loading ...
Loading ...
Loading ...