Loading ...
Loading ...
Loading ...
9
English
5. If driver blade is in the down position, cycle stall
release lever (M) using enough force to fully slide
it to the other end of the slot in housings.
6. Close the front door and engage the latch pin
under the two arms (N) on the nosepiece. Push
latch until it locks in place.
7. Reinsert battery pack.
NOTE: The tool will disable itself and not reset
until the battery pack has been removed and
reinserted.
8. Reinsert nails into magazine (see Loading the
Tool).
NOTE: Should nails continue to jam frequently in
nosepiece, have tool serviced by an authorized
D
e
WALT service center.
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 5 or 6 times into scrap lumber
before using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct sunlight as excessive heat can
deteriorate bumpers and other rubber parts resulting in increased maintenance.
Suspension Hook (Fig. 12)
The D
e
WALT cordless nailers include an integrated
suspension hook (J) and can be attached to either side
of the tool to accommodate left- or right-handed users.
If the hook is not desired at all, it can be removed from
the tool.
TO REMOVE SUSPENSION HOOK
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage
simply remove the screw (P) from the opposite side
of the tool and reassemble on the other side.
3. Replace battery pack.
WARNING: Remove nails from magazine before making any adjustments or servicing this
tool. Failure to do so may result in serious injury.
WARNING: Disconnect battery pack from tool before making any adjustments,
changing accessories, servicing, or moving the tool. Such preventative safety
measures reduce the risk of starting the tool accidentally.
CAUTION: When not in use, place tool on its side on a stable surface where it
will not cause a tripping or falling hazard. Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
FIG. 12
J
P
3. Open the jam clear door on the nosepiece to verify there are no nails remaining.
Adjusting Depth (Fig. 9)
The depth that the fastener is driven can be adjusted using the depth adjustment wheel
(C) on the side of the tool.
WARNING: To reduce risk of serious injury from accidental actuation when
attempting to adjust depth, ALWAYS:
• Remove battery pack.
• Engage trigger lock-off.
• Avoid contact with trigger during adjustments.
1. To drive the nail shallower , rotate the depth adjustment wheel (C) away from the nose
of the nailer.
2. To sink a nail deeper , rotate the depth adjustment wheel (C) toward the nose of the
nailer.
FIG. 9
C
Headlights (Fig. 10)
There is a headlight (D) located on each side of the nailer.
Headlights turn on upon battery insertion, activation of
the trigger, or depressing the contact trip. The lights
will automatically shut off after 20 seconds unless tool
remains in use.
NOTE: These headlights are for lighting the immediate
work surface and are not intended to be used as
flashlights.
LOW BATTERY INDICATOR: The left-side headlight
will flash four consecutive times and then shut down to
indicate low battery.
JAMMED NAIL INDICATOR: The right-side headlight will flash continually if a nail becomes
jammed in the nosepiece (see Clearing a Jammed Nail).
Clearing a Jammed Nail (Fig. 11)
If a nail becomes jammed in the nosepiece, keep the tool pointed away from you and follow
these instructions to clear:
1. Remove battery pack from tool and engage the trigger lock-off.
2. Pull the pusher back and remove any loaded nails.
3. Lift the jam clearing latch (E) then pull up to open front door (O).
4. Remove bent nail, using pliers if necessary.
D
FIG. 10
O
E
N
FIG. 11
Loading ...
Loading ...
Loading ...