KBBL306ESS User Manual

Loading ...

PERFORMANCE DATA SHEETS

Base Grille Water Filtration System

Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)

Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance Reduction

Aesthetic Effects

NSF

Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Chlorine Taste/Odor

Particulate Class II*

50% reduction

85% reduction

2.0182 mg/L

1333333 #/mL

2.0 mg/L ± 10%

At least

10,000 particles/mL

0.06 mg/L

6600 #/mL**

0.0536 mg/L

2325 #/mL

97.03%

99.51%

97.34%

99.83%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Lead: @ pH 6.5 ***

Lead: @ pH 8.5 ***

0.010 mg/L

0.1533 mg/L

0.1400 mg/L

0.15 mg/L ± 10%

0.0005 mg/L

0.0007 mg/L

0.0005 mg/L

0.0006 mg/L

99.67%

99.50%

99.67%

99.57%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.0058 mg/L

0.0059 mg/L

0.006 mg/L ± 10%

0.0002 mg/L

0.0005 mg/L

0.0002 mg/L

0.0003 mg/L

96.54%

91.57%

96.54%

94.92%

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 0.0006 mg/L 92.22% 96.34%

O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58% 99.63%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.001 mg/L 93.3% 93.3%

Carbofuran 0.040 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L 0.0213 mg/ 51.13% 74.00%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■ It is essential that operational, maintenance, and lter

replacement requirements be carried out for the product to

perform as advertised.

■ Use replacement lter T2RFWG2, part #4396841.

Model T1WG2L: Style 1 – When the lter indicator reads

10%, order a new lter. When the indicator reads 0%, it is

recommended that you replace the lter.

Style 2 – When the lter indicator changes from green to

yellow, order a new lter. When the indicator changes from

yellow to red, it is recommended that you replace the lter.

Style 3 – When the water lter status display changes from

“GOOD” to “ORDER,” order a new lter. When the lter

indicator reads “REPLACE,” it is recommended that you

replace the lter.

Style 4 – Press FILTER to check the status of your water lter.

If the lter indicator light is yellow, order a new lter. If the lter

indicator light is red, it is recommended that you replace the

lter.

Model T1WG2: Change the water lter cartridge every 6

months. If the water ow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace

the water lter cartridge more often.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

■ Refer to the “Warranty” section for the Manufacturer’s name,

address and telephone number.

■ Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

35 - 120 psi (241 - 827 kPa)

33° - 100°F (1° - 38°C)

0.85 gpm (3.2 L/min.) @ 60 psi*

System tested and certied by NSF International against NSF/ANSI Standard 42 for

the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI

Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene,

and Carbofuran.

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dus

***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.

NSF is a registered trademark of NSF International.

Loading ...

User Manual - Page 16