SDD2LEMTC580 User Manual

Loading ...

S-DD2-L FLUSH TOP 17

INSTALLING THE

COOKER HOOD

1. Before carrying out the appliance installa-

tion, please check that all components are

not damaged, in such a case contact your

retailer and do not carry out any installation

operation.

Before the installation of the Downdraft,

please remove the safety piece you can see

in the picture (Fig. 1). Furthermore, please

read carefully all of the following installation

instructions.

 • Useanairexhaustingpipewhosemaxi-

mum length does not exceed 5 meters.

 • Limitthenumberofelbowsinthepiping,

since each elbow reduces the air capac-

ity of 1 linear meter. (Ex. : if you use no. 2

x 90 ° elbows, the length of piping should

not exceed 3 meters).

 • Avoidabruptdirectionchanges.,

 • Use a 150 mm. constant diameter pipe

for the whole length.

 • Use piping approved by standards in

force.

The manufacturer shall not be deemed re-

sponsible for air capacity or noise problems

caused by failure to comply with the above

instructions and no warranty on the product

shall be provided.

2. Before making the hole, check that there are

no structural or other parts inside the cabi-

net, where the appliance is to be placed,

which could hinder a proper installation.

Check that the dimensions of the Downdraft

and the ones of the cook top are compatible

with the cabinet so that the installation can

be carried out properly.

3. Make a rectangular opening, 842 x 100 mm

in size, in the back of the cook top for the 90

cm model and 542 x 100 mm for the 60 cm

model and 1142 x100 mm for the 120 cm

model. In the version with the motor already

installed, remove the screws and the suc-

tioning unit in order to insert the down-draft

in the hole made.

4. Put the Downdraft in the opening, inserting it

from above as shown in (Fig. 2).

5. Fix the downdraft inside the cabinet, using

the special fixing brackets supplied with the

product (Fig. 3).

Insert the brackets in the lower side of the

downdraft (Fig. 3), in such a way that there

is a 2 mm distance between the lower side

of bracket and the bottom of the cabinet

(Fig. 3).

This distance will allow the traction to be po-

sitioned downwards of the product, at the

moment of fixing, in order to have the stain-

less steel trim perfectly adhering with the

work surface. Before inserting the screws,

please make sure that the appliance is per-

fectly perpendicular with the work surface.

6. Once the installation is complete and after

connecting the appliance to the mains pow-

er, lift up the downdraft and remove the door

block (Fig. 4); then open the door (Fig. 5)

and fit the filters in place (Fig. 6). In the ver-

sion of the Downdraft equipped with internal

motor, install the power unit orienting the air

outlet to the desired position, either down-

wards or upwards (Fig. 7).

The motor can be installed either on the front

or rear side of the downdraft After having in-

stalled the motor, connect the air ducts.

7. For versions with external motor, place the

suctioning unit (external motor) in a suitable

area and fit the exhaust air flue as illustrated.

Then fit the air outlet ducts between the ex-

ternal motor and the downdraft. Select an air

outlet from the five possibilities (Fig. 9) and

fit the union supplied with the appliance.

8. Place the metal box with the electronic com-

ponents in an easily reachable area for even-

tual technical assistance operations. (Fig.

9), connecting the three connectors (9 pole

connector for the actuator control and the

safety control, 4 pole connector for neon

lamp turn on and push-button connector)

(Fig. 10).

Loading ...

User Manual - Page 17