Loading ...
Loading ...
Loading ...
15
EN
When using the two preset cycles “Wash & Dry
45’” and “Wash & Dry 90’”, it is not necessary to
select and start a drying cycle.
Dry only
This function is used to simply dry a wet load
washed previously in the washer dryer or by
hand.
1. Select a programme that's compatible with
the type of garments to be dried (e.g. select
cotton if you want to dry a load of wet cotton
garments).
2. Press the “Dry only” button to perform the
drying cycle alone, without performing the
wash cycle.
3. Select the desired drying mode by pressing the
“Drying settings” button.Two drying modes are
available: automatic or timer.
- Automatic drying with selectable levels:
In automatic drying mode, the washer dryer
machine dries the laundry until the set level
of dryness is reached. As soon as the "Drying
settings" button has been pressed, the washer
dryer automatically selects the maximum drying
level compatible with the selected programme.
Press the button again to reduce the drying level.
The following levels are available:
Wardrobe : laundry is completely dry and
ready to be put away in the wardrobe without
ironing.
Hanger : laundry is left slightly damp to
minimise creasing. Garments must be hung to
air dry completely.
Iron : garments are left reasonably damp to
make ironing easier.
- Timer drying mode:
If you want to set a timed drying cycle, press the
“Drying settings” button repeatedly. After all the
automatic drying levels have been displayed,
continue pressing the “Drying settings” button
until the desired time is displayed. Values from
210 to 30 minutes are settable.
N.B.: always allow a cooling down period after
drying before opening the door.
5. USING THE CORRECT AMOUNT OF
DETERGENT.
Extract the dispenser and pour the detergent
into the appropriate trays as explained in the
section titled “Detergent Dispenser”. Only if
you want to perform a wash or wash + dry
programme.
6. DELAYING THE START OF A PROGRAMME.
If you want to delay the programme's
activation, see the section titled“Programmes
and Options”.
7. STARTING A PROGRAMME.
Press the START/PAUSE button. The relative
indicator lamp illuminates, the door locks
and the door open symbol extinguishes.
To change a programme while a cycle is in
progress, set the washer dryer to pause mode
by pressing the START/PAUSE button (the
START/PAUSE indicator light will slowly ash
with an amber colour); next, select the desired
cycle and press the START/PAUSE button again.
To open the door while a cycle is in progress,
press the START/PAUSE button; if the symbol
turns on, the door can be opened. Press the
START/PAUSE button again to resume the
programme from the point at which it was
interrupted.
8. CANCELLING A PROGRAMME IN PROGRESS IF
NECESSARY
Press and hold the button until the washer
dryer stops.
If the water level and temperature are low
enough, the door unlocks and may be opened.
The door remains locked if there is water in the
drum. To unlock the door, switch the washer
dryer on, select the SPIN & DRAIN programme
and turn the spin function o by setting the
spin speed to 0. The water is emptied and the
door unlocks at the end of the programme.
9. SHUT OFF THE WASHER DRYER AT THE END
OF THE PROGRAMME.
At the end of the cycle, the message “END” is
shown on the display. The door can only be
opened once the symbol turns on. Check
that the door unlocked symbol is lit, then open
the door and take out the laundry.
Press to switch the washer dryer o. To save
energy, if the washer dryer is not switched
o manually with the button, it turns o
automatically approximately 30 minutes after
the end of the programme.
Leave the door slightly ajar in order to allow the
inside of the washer dryer to dry.
Loading ...
Loading ...
Loading ...