Loading ...
5
Alignment
Loud noise formation, intense vibrations and ”wandering” may be due to incorrect
alignment!
Align washing machine with spirit level.
1. Loosen lock nut in a clockwise direction with a wrench.
2. Change height by rotating the appliance feet.
All four appliance feet must be firmly on the floor.
The washing machine must not wobble!
Check alignment of the washing machine (if available with a spirit level)
and,if required, correct.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Product standard
The washing machine carry out the national standard as following:
GB 4706.1
GB 4706.24
GB 19606
GB 4343.1
GB 17625.1
GB/T 4288
GB 12021.4
lock nut
appliance
foot
0613/9000372388Manufacturer (see Operating instructions)
6
Electrical connection
ʑ
Connect the washing machine to an alternating current via a correctly
installed earthed socket only.
ʑ
The main voltage and specifications on the washing machine must
match the nameplate at the back of machine at the installation location.
ʑ
Connected load and required fuse or line protecting cut-out are
indicated on the nameplate.
ʑ
Ensure that:
– the mains plug and socket are compatible,
– the main plug is easy to reach,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
ʑ
A damaged power cord may be only replaced by special power cord or
power cord from the manufacture or customer service center. Replace
by an electrician only.
ʑ
Do not use multiple plugs/couplings or extension cables.
ʑ
If an earth-leakage circuit-breaker is used, use only a type which
features this symbol: 7 .
Only this symbol guarantees compliance with the current valid
regulations.
ʑ
Mains plug:
– do not insert/pull out of the socket with damp hands.
– do not pull the plug out of the socket by tugging the power cord.
– never pull out of the plug while the appliance is operating.
7
Transportation, e.g. if moving house
Before transporting the washing machine:
1. Turn off the tap.
2. Release the water pressure in the water inlet hose.
a Operating instructions ; Filter in the water inlet hosey .
3. Drain any residual detergent solution.
a Operating instructions ; Detergent solution pump.
4. Isolate the washing machine from the power supply.
5. Remove the hoses.
Installing transportation bolts
For WM,WAX,WAE
ʑ
Remove the four cover caps C.
ʑ
Remove the rear cover D and prepare the
transportation bolts.
ʑ
Insert and tighten the transportaion bolts.
For WS,WLX
ʑ
Remove the four cover caps.
ʑ
Prepare the four transportation bolts.
Pull the bolt out of the sleeve until the end of the bolt
is flush with the end of the sleeve.
ʑ
Insert and tighten the bolts. The lug on the washer
must be located in the groove in the rear cover.
The transportation bolts m
ust be removed after transportation.a Page 3.
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the D
rain or Spin programme.
1.
2.
D
C
Installation instructions
Contents Page
ʋSafety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋEnvironmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋInstallation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋBuilt-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . 1
ʋStandard accessories at the back of machine . . . . . . . 2
ʋHose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
ʋRemoving transportation bolt . . . . . . . . . . . . . . . . . . . . 3
ʋWater connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ʋAlignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋProduct standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋElectrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ʋTransportation, e.g. if moving hous . . . . . . . . . . . . . . . . 7
Washing
machine
Read installation instructions before switching on the washing machine!
Also follow the separate Operating instructions.
Any fault or loss caused by not following installation instructions or operating
instructions is not in the arrange of the warranty, and in this case manufacture
has no responsibility.
Retain all documents for subsequent use or for the next owner.
If in doubt, please contact the local customer service center.
en
Loading ...
Loading ...
Loading ...