Loading ...
Loading ...
Loading ...
Cleaning function en
31
.Cleaning function
Cl eani ng function
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
Caution!
■ Risk of damage to the appliance: Only use the
descaler recommended by us for descaling, either in
liquid or tablet form.The time the descaler needs to
be left to work depends on the product used.Other
descalers may damage the appliance. You can
order descaler from our after-sales service.
Liquid descaler: Order no. 00311680 Descaling
tablets: Order no. 00311864
■ Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This may damage the surfaces. If this does happen,
remove the descaling solution immediately with
water.
Descaling consists of two automated steps. For hygiene
reasons, the descaling program must be run through
completely before the appliance is ready for operation
again. Descaling will take around 32 minutes in total.
■ Descale the appliance (approx. 31 minutes), then
empty the drip tray and fill the water tank with fresh
water.
■ Run a rinse cycle after descaling the appliance
(approx. 1 minute), then empty the drip tray.
If descaling is interrupted (e.g. due to a power failure,
because the appliance is switched off or because the
descaling process is cancelled), you will be prompted
to run a rinse cycle once the appliance is switched back
on.The appliance cannot be used until the rinse cycle
comes to an end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible (or fewer), the Ê symbol appears on the
appliance display, reminding you to descale it. You can
therefore prepare for the descaling in good time.
The steam mode is then only possible after the
descaling process has been completed.
Starting
1. Use the function selector to select Descale Ê.
The duration of the descaling process will be
displayed.It cannot be changed.
2. Open the tank cover.
3. Remove and empty the drip tray.
4. Slide the empty drip tray in fully.
5. Remove the water tank.
6. Mix water and descaler to create a descaling
solution.
Note: Observe the mixing ratio of the descaling
agent.
Descaling liquid (Order no. 00311680): Mixing ratio
1:5, mix 50ml descaling liquid with 250ml water.
Descaling tablets (Order no. 00311864): Add one
descaling tablet (18g) to 250ml water and let
dissolve for five minutes.
7. Pour the descaling solution into the water tank and
slide the water tank in fully.
8. Close the tank cover.
9. Touch the start l stop button.
The appliance will now be descaled. The remaining
time counts down on the display. An audible signal
will sound once descaling has finished.The
appliance pauses.
10. Open the tank cover.
11. Remove the drip tray, empty it and slide it back in.
12. Remove the water tank, rinse it thoroughly, fill it with
fresh water and slide it back in.
13. Close the tank cover.
14. Touch the start l stop button.
The appliance will now be rinsed twice automatically.
An audible signal will sound once the rinse cycles
have finished. Empty the drip tray.
Rinsing
To ensure that your appliance stays clean, you can
pump water through the pipe system. The water is then
drained to the drip tray.
Note: After rinsing, there can be dissolved lime
particles in the drip tray. This is normal and does not
affect operation.
Starting
1. Use the function selector to select the rinse cycle !.
The duration of the programme will be displayed.It
cannot be changed.
2. Open the tank cover.
3. Remove and empty the drip tray.
4. Slide the empty drip tray in fully.
5. Remove water tank and drain any residual water.
Rinse out water tank thoroughly and fill with fresh
water.
6. Slide the water tank in fully.
7. Close the tank cover.
8. Touch the start l stop button.
Water is pumped through the pipes.The time
remaining will count down on the display. An audible
signal will sound once this time has elapsed. Empty
the drip tray.
Subsequent cleaning
Carry out the following steps after every descaling
programme or rinse cycle:
1. Open the tank cover.
2. Empty, clean and dry the drip tray and water tank.
3. Turn the function selector to the off position.
The process is complete and the appliance is ready
for use again.
Loading ...
Loading ...
Loading ...